Translations:StudioXm:Connection/13/en: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
← Older editNewer edit →
FuzzyBot (talk | contribs)
8,120 edits
Importing a new version from external source
FuzzyBot (talk | contribs)
8,120 edits
Importing a new version from external source
Line 1: Line 1:
= Connection to StudioX app=
= Connection to StudioX Flow app=
If not already done start StudioX now. When using a computer with Windows or macOS, click the '''OPTIONS''' button on top right corner and choose the type of interface there firstly. Then proceed as follows.<br />
On a Windows or mac computer you can connect either per USB or Bluetooth. With smartphone/tablet only Bluetooth can be used. Click the USB or BLE symbol to initiate connection to your BEASTX device. In the following you'll see a list of ports/interfaces that have been found. Choose the port name that belongs to your interface.<br />
<br />
<br />
When the <b>USB2SYS</b> is connected to the computer, make sure the corresponding port is selected in the selection box in the middle of the screen. If you have connected it after starting the software, click the '''RESCAN''' button above to refresh the port list, usually the correct port will be selected automatically then. If you don't know which port is the right one, also you can disconnect the USB2SYS once again, click RESCAN to clear the port list, connect the USB2SYS, wait a few seconds and click RESCAN once more. Now the port should be selected.<br />
The <b>USB2SYS</b> is usually named /dev/tty.usbserial-0001 or /dev/tty.SLAB_USBtoUART on macOS computers. On Windows systems it'll be named COMxy. If you can't find out which port name your device has, simply disconnect the USB once and click the background to abort connection. Click "Scan USB" button again and check out the names on the device list. Click the background again, reconnect USB2SYS and click "Scan USB" button again. Now choose the item, that was not there before.<br />
<br />
<br />
With the <b>BLE2SYS</b> in combination with a smartphone/tablet the BLE2SYS device should appear automatically when starting the app after powering up your flybarless device with BLE2SYS. If this is not the case, click the selection box and choose "BLE2SYS". If nothing's there, click the '''RESCAN''' button above to search for new devices. This can take from a few seconds up to a few minutes. '''If the scan process finishes immediately and the box stays empty it is very likely the bluetooth function is switched off on your phone or the app has no rights to access the bluetooth connection!''' So check your phone settings in this case.<br />
With the <b>BLE2SYS</b> the device in the list usually is named "BLE2SYS" unless the name wasn't changed by the user. Here the scan process usually takes around 5 seconds. '''If the scan process finishes immediately and the box stays empty it is very likely the bluetooth function is switched off on your phone/computer or the app has no rights to access the bluetooth connection!''' So check system settings of your device in this case.<br />
<br />
<br />
Then connect the USB/BLE Interface to the [SYS] port of your BEASTX device and power everything up. Click '''CONNECT''' to load the data from your device and to enter configuration menus. In case you are asked for the BLE2SYS pin code, this usually is 1111. If that doesn't work, please try 0000 or 1234.<br />
In case you are asked for the BLE2SYS pin code, this usually is 1111. If that doesn't work, please try 0000 or 1234.<br />
<br />
<br />
<br />
<br />
<html>
{|
<div class="ios-gallery-container">
|style= "padding: 0px 50px;" | [[File:Connect dialog.png|x250px]]
        <!-- Erstes Bild und Text -->
|style= "padding: 0px 50px;" | [[File:Mainscreen usbports.png|x250px]]
        <div class="ios-gallery-item">
|}
            <div class="ios-gallery-image">
                <img src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20006.PNG" alt="Screenshot">
            </div>
            <div class="ios-gallery-text"></div>
        </div>
        <div class="ios-gallery-item">
            <div class="ios-gallery-image">
                <img src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20007.PNG" alt="Screenshot">
            </div>
            <div class="ios-gallery-text"></div>
        </div>
</div>
</html>
<br />
<br />
<br />
<br />
{{SHORT_QUOTE|width=100|When connection fails, <b>on the computer</b> once again check driver installation and port configuration. When your BLE2SYS is not found, check if the BLE2SYS it is operating properly: The blue LED must flash in short intervals. Note that by default the interface will switch off automatically after 30 seconds. So if you need too long time to initiate connection it may have been disabled. Disconnect it or cylce power and try again. <b>Sometimes it can be helpful to close the app completely, disconnect and reconnect the BLE2SYS and start over again!</b><br />
'''Autoconnect option'''<br />
Please note that it's possible to speed up connection sequence once you've determined the interface name. Go to "Settings" and enable the "Autoconnect" button. When using StudioX Flow later onwards, it'll automatically recognize the listed device names and will connect with these if they're present.<br />
<br />
<br />
Also note that the device name can be different! By default it's "BLE2SYS", but as it's possible to change the bluetooth id, it maybe different.}}<br />
{|
|width = "400pt" style= "padding: 0px 50px;" | [[File:Settings autoconnect.png|x250px]]
|}
<br />
<br />
<br />
<br />

Revision as of 12:47, 31 March 2026

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (StudioXm:Connection)
= Connection to StudioX Flow app=
On a Windows or mac computer you can connect either per USB or Bluetooth. With smartphone/tablet only Bluetooth can be used. Click the USB or BLE symbol to initiate connection to your BEASTX device. In the following you'll see a list of ports/interfaces that have been found. Choose the port name that belongs to your interface.<br />
<br />
The <b>USB2SYS</b> is usually named /dev/tty.usbserial-0001 or /dev/tty.SLAB_USBtoUART on macOS computers. On Windows systems it'll be named COMxy. If you can't find out which port name your device has, simply disconnect the USB once and click the background to abort connection. Click "Scan USB" button again and check out the names on the device list. Click the background again, reconnect USB2SYS and click "Scan USB" button again. Now choose the item, that was not there before.<br />
<br />
With the <b>BLE2SYS</b> the device in the list usually is named "BLE2SYS" unless the name has been changed by the user. Here the scan process usually takes around 5 seconds. '''If the scan process finishes immediately and the box stays empty it is very likely the bluetooth function is switched off on your phone/computer or the app has no rights to access the bluetooth connection!''' So check system settings of your device in this case.<br />
<br />
In case you are asked for the BLE2SYS pin code, this usually is 1111. If that doesn't work, please try 0000 or 1234.<br />
<br />
<br />
{|
|style= "padding: 0px 50px;" | [[File:Connect dialog.png|x250px]]
|style= "padding: 0px 50px;" | [[File:Mainscreen usbports.png|x250px]]
|}
<br />
<br />
'''Autoconnect option'''<br />
Please note that it's possible to speed up connection sequence once you've determined the interface name. Go to "Settings" and enable the "Autoconnect" button. When using StudioX Flow later onwards, it'll automatically recognize the listed device names and will connect with these if they're present.<br />
<br />
{|
|width = "400pt" style= "padding: 0px 50px;" | [[File:Settings autoconnect.png|x250px]]
|}
<br />
<br />

Connection to StudioX Flow app

On a Windows or mac computer you can connect either per USB or Bluetooth. With smartphone/tablet only Bluetooth can be used. Click the USB or BLE symbol to initiate connection to your BEASTX device. In the following you'll see a list of ports/interfaces that have been found. Choose the port name that belongs to your interface.

The USB2SYS is usually named /dev/tty.usbserial-0001 or /dev/tty.SLAB_USBtoUART on macOS computers. On Windows systems it'll be named COMxy. If you can't find out which port name your device has, simply disconnect the USB once and click the background to abort connection. Click "Scan USB" button again and check out the names on the device list. Click the background again, reconnect USB2SYS and click "Scan USB" button again. Now choose the item, that was not there before.

With the BLE2SYS the device in the list usually is named "BLE2SYS" unless the name wasn't changed by the user. Here the scan process usually takes around 5 seconds. If the scan process finishes immediately and the box stays empty it is very likely the bluetooth function is switched off on your phone/computer or the app has no rights to access the bluetooth connection! So check system settings of your device in this case.

In case you are asked for the BLE2SYS pin code, this usually is 1111. If that doesn't work, please try 0000 or 1234.




Autoconnect option
Please note that it's possible to speed up connection sequence once you've determined the interface name. Go to "Settings" and enable the "Autoconnect" button. When using StudioX Flow later onwards, it'll automatically recognize the listed device names and will connect with these if they're present.



Retrieved from "https://wiki.beastx.com/index.php?title=Translations:StudioXm:Connection/13/en&oldid=26172"