Help:FAQ Nanobeast/de: Difference between revisions
Shornstein (talk | contribs) No edit summary |
Updating to match new version of source page |
||
| Line 14: | Line 14: | ||
[[File:Nanobeast_Programming.PNG|x300px|border]]<br /> | [[File:Nanobeast_Programming.PNG|x300px|border]]<br /> | ||
<br /> | <br /> | ||
= NANOBEAST firmware recovery process = | |||
When it isn't possible to establish connection with NANOBEAST from StudioX Flow app by USB2SYS or BLE2SYS please try to connect using the firmware recovery mode.<br /> | |||
<br /> | |||
'''Required items:''' | |||
* power source 5 - 8 Volts (i.e. 2s LiPo battery or BEC power from helicopter ESC) | |||
* jumper wire with apprx. 10 - 15cm length<br /> | |||
<br /> | |||
'''Putting device into boot mode:''' | |||
* Connect jumper wire to signal pin of SYS port. (When looking from the front it's the bottom pin on the very left.<br /> | |||
<br /> | |||
[[File:Nanobeast jumperwire front.jpg|x200px|none]]<br /> | |||
* Connect other end of the jumper wire to signal pin of CH5. (When looking from top on the NANOBEAST CH5 is the last socket at the bottom. The signal pin again is on the left here.)<br /> | |||
<br /> | |||
[[File:Nanobeast jumperwire top.jpg|x200px|none]]<br /> | |||
* Now connect the power source to the DI port which is above SYS port. (Watch out for correct polarity). The Status LED will show red color immediately.<br /> | |||
<br /> | |||
[[File:Nanobeast bootmode poweron.jpg|x200px|none]] | |||
<br /> | |||
* Remove jumper wire while keeping device powered and attach USB2SYS or BLE2SYS to SYS port.<br /> | |||
<br /> | |||
[[File:Nanobeast bootmode poweronble.jpg|x200px|none]] | |||
<br /> | |||
* Finally: Connect with StudioX Flow. It should indicate Recovery Mode now.<br /> | |||
<br /> | |||
[[File:StudioXFlow Nanobeast recoverymode.png|x200px|none]] | |||
<br /> | |||
* Click menu on the top left corner and go to '''Firmware Update''' screen. Flash latest firmware on the device. (Don't worry, usually it won't erase all your settings. The warning maybe incorrect as StudioX Flow will not be able to check settings version!)<br /> | |||
<br /> | |||
[[File:StudioXFlow FirmwareUpdate Recovery.png|x200px|none]] | |||
[[File:StudioXFlow FirmwareUpdate Nanobeast.png|x200px|none]] | |||
[[File:StudioXFlow FirmwareUpdate EraseWarning.png|x200px|none]] | |||
<br /> | |||
* After update process StudioX Flow will reconnect automatically and should indicate successful firmware update.<br /> | |||
<br /> | |||
[[File:StudioXFlow Nanobeast Mainscreen.png|x200px|none]] | |||
<br /> | |||
<br /> | |||
<br /> | |||
<!-- | <!-- | ||
Revision as of 16:47, 19 April 2026
Programmierung mit dem externen Tastschalter
Der Shape S2 Heli wird mit einem kleine Tastschalter ausgeliefert, der über einen Knopf und 3 DIP Schalter verfügt. Das Nanobeast auf dem Shape S2 ist vorprogrammiert, so dass es nicht notwendig ist, die Grundeinstellung über die StudioX App zu machen. Stattdessen muss lediglich das Fernsteuersystem eingerichtet werden und dann muss einmal der Fernsteuersystem am Nanobeast angelernt werden. Hierfür wird der Tastschalter benötigt. Weitere Infos findes Du im Shape S2 Handbuch.
Zur Info: Tatsächlich wird derzeit nur der Knopf für die Programmierung benötigt. Die 3 DIP Schalter haben bei der aktuellen Firmware keine Funktion. Möglicherweise finden sie bei künftigen Versionen Verwendung.
Noch ein Hinweis: Der Tastschalter kann auch mit der Standard Nanobeast Firmware verwendet werden, um den Empfängerscan zu starten. Wie das genau funktioniert, das steht im Shape S2 Handbuch (kurz: Tastschalter an SYS anstecken, Gerät einschalten, während die LED rot blinkt den Knopf drücken und halten, loslassen wenn die LED dauerhaft leuchtet, dann nochmal kurz auf den Knopf drücken zum Starten des Scanvorgangs).
NANOBEAST firmware recovery process
When it isn't possible to establish connection with NANOBEAST from StudioX Flow app by USB2SYS or BLE2SYS please try to connect using the firmware recovery mode.
Required items:
- power source 5 - 8 Volts (i.e. 2s LiPo battery or BEC power from helicopter ESC)
- jumper wire with apprx. 10 - 15cm length
Putting device into boot mode:
- Connect jumper wire to signal pin of SYS port. (When looking from the front it's the bottom pin on the very left.
- Connect other end of the jumper wire to signal pin of CH5. (When looking from top on the NANOBEAST CH5 is the last socket at the bottom. The signal pin again is on the left here.)
- Now connect the power source to the DI port which is above SYS port. (Watch out for correct polarity). The Status LED will show red color immediately.
- Remove jumper wire while keeping device powered and attach USB2SYS or BLE2SYS to SYS port.
- Finally: Connect with StudioX Flow. It should indicate Recovery Mode now.
- Click menu on the top left corner and go to Firmware Update screen. Flash latest firmware on the device. (Don't worry, usually it won't erase all your settings. The warning maybe incorrect as StudioX Flow will not be able to check settings version!)
- After update process StudioX Flow will reconnect automatically and should indicate successful firmware update.
