All translations
Jump to navigation
Jump to search
Enter a message name below to show all available translations.
Found 2 translations.
| Name | Current message text |
|---|---|
| h German (de) | ==Direktanteil== Der Direktanteil beeinflusst den Anteil vom Steuerknüppelsignal (Roll/Nick), der direkt (am Regelkreis vorbei) auf die Servos ausgegeben wird. Das sorgt dafür, dass der Regelkreis entlastet wird und die Steuerkommandos schneller umgesetzt werden. Ziel ist es, dass die Taumelscheibe von Hand möglichst nahe an den benötigten Ausschlag gesteuert wird und der Regelkreis nur noch kleinere Abweichungen korrigieren muss.<br /> <br /> Eine Erhöhung des Direktanteils bewirkt also, dass mehr Steuersignal vom Knüppel direkt auf die zyklische Funktion (Roll/Nick) der Taumelscheibe aufgemischt wird. Ist der Direktanteil jedoch zu hoch, so wird die jeweilige Funktion übersteuert und die Präzision lässt nach. Der Regelkreis muss dann zusätzlich zu den äußeren Einflüssen auch den zu großen Steuerausschlag korrigieren. Das Steuergefühl wirkt dann zwar sehr "direkt", weil die Servos eine Knüppelbewegung sofort umsetzen. Es werden dadurch aber ungewollte Effekte auftreten wie z.B. ein Zurückschwingen bei Stopps oder starkes Aufbäumen bzw. Unterschneiden schon bei kleinsten Steuerbewegungen im schnellen Vorwärtsflug. Ist der Direktanteil zu niedrig eingestellt, so wirkt die Reaktion auf Steuerbefehle sehr weich und verzögert.<br /> <br />Im Idealfall ist der Direktanteil gerade so hoch eingestellt, dass der Helikopter zwar sehr unmittelbar und direkt auf Steuerbefehle reagiert, aber gleichzeitig auch die Steuerbefehle sehr sauber und präzise umsetzt. Der optimale Direktanteil ist von vielen Faktoren abhängig wie z. B. Hauptrotorblätter, Servos, Rotordrehzahl sowie Masse und Größe des Helikopters.<br /> <br /> <br /> {{QUOTE|Der Direktanteil beeinflusst nicht die maximale Drehrate! Sollte der Helikopter zu langsam drehen, so verändere das Steuerverhalten im Parametermenü unter Einstellpunkt B. Überprüfe auch die Einstellung der Wegbegrenzung der Taumelscheibe im Setupmenü.<br /> <br /> Für ein schnelleres und aggressiveres Ansprechen ist ebenfalls Einstellpunkt B im Parametermenü anzupassen (Expo reduzieren, Gesamtdrehrate erhöhen). Außerdem kann das zyklische Ansprechverhalten über Einstellpunkt G im Parametermenü optimiert werden. Ein vergrößern des Direktanteils über den optimalen Punkt hinaus wird hingegen nicht empfohlen, da es sich zwar "direkter" anfühlt, jedoch zu einem Verlust der Steuerpräzision führt!}}<br /> <br /> |
| h English (en) | ==Cyclic feed forward== This part mixes some amount of stick input directly to the servos, bypassing the control loop. If correctly adjusted, the feed forward relieves the control loop so it will work more efficiently by only having to make residual corrections. Factory setting of the dial is horizontal which provides a good setup in most cases. Turn dial 2 clockwise to increase the cyclic feed forward. This will cause more cyclic stick input going directly to aileron and elevator on the swashplate. Decreasing the direct stick feed forward will do the opposite.<br /> <br /> In case the cyclic feed forward is set too high, the stick input will over control the cyclic input from the control loop. Eventually the control loop needs then to steer back and compensate the unwanted cyclic movement. Even though you get the impression to have a more direct and immediate control over the servos with high feed forward values, unwanted side effects may appear, like pitching back on cyclic stops and imprecise fast forward flight.<br /> <br /> If the direct cyclic feed forward is too low, the helicopter will feel softer, slower and less "connected". The optimal point depends of many factors like blades, servos, head speed, size and mass of the helicopter. Ideally you can increase the feed forward just as high as possible without any negative effects happening. So you get a quite natural stick feeling and the control loop is supported as good as possible. Before adjusting the cyclic feed forward you should try to find the optimal maximum cyclic gain first (see above). Then adjust the cyclic feed forward and after that, you may have to adjust the cyclic gain once again, as both parameters interact to each other.<br /> <br /> <br /> {{QUOTE|The cyclic feed forward does not affect the maximum rate of rotation! If the helicopter turns too slow, you should check the settings of the swashplate limiter in [[Manuals:BXFbl:Setupmenu_L/en|Setup menu point '''L''']], change the control behavior at [[Manuals:BXFbl:ControlStyle/en|Parameter menu point '''B''']] or increase the servo travels or "Dual Rate" setup of your transmitter.<br /> <br /> Also to get a quicker and more aggressive response, change the control style at [[Manuals:BXFbl:ControlStyle/en|Parameter menu point '''B''']] (reducing expo and increasing the maximum rotation rate) and increase the cyclic response at [[Manuals:BXFbl:Parametermenu/en|Parameter menu point '''G''']]. It is not recommended to increase the feed forward in this case! Although it may produce a quicker servo movement and more direct stick feel at first glance, you will get negative effects on overall performance as described above.}}<br /> <br /> |