MICROBEAST ULTRA V5

1. Introduction

2. Safety notes

3. Box content and accessories

4. Hardware installation

5. Receiver connection

6. Radio system

7. Receiver Menu

Receiver type

Function assignment

Telemetry input

Throttle failsafe

8. Basic setup

Device orientation

Swashplate servos

Rudder pulse width

Rudder frequency

Rudder control

Swash mixing

Servo directions

Cyclic directions

Servo trim

Cyclic throw

Collective pitch

Servo limit

9. Headspeed Governor

Activating the governor

Sensor test mode

Throttle low position

Throttle high position

Transmitter setup

Signal divider

Main gear ratio

10. Parameters

Gain adjustment

Trimming

Control style

Special parameters

11. Optional features

AttitudeControl (setup)

AttitudeControl (usage)

Bank Switching

Telemetry

12. Factory reset

13. Version information

14. Firmware update

→

MICROBEAST ULTRA - What's that?

MICROBEAST ULTRA is a gyro system which is used to stabilize and control your flybarless RC Helikopter on all three flight axis. It can be used with many different types of helicopters like 3D aerobatic helis, F3C competition helicopters as well as scale helicopters with 2 or more rotorblades. MICROBEAST ULTRA ist the successor of the well proven MICROBEAST PLUS, featuring a modern ARM Cortex M4 microcontroller with lots of processing power. Like MICROBEAST PLUS the system comes with basic flybarless stabilization functionality and can be upgraded for additional features by paid update.

Please note: MICROBEAST ULTRA is also sold as MICROBEAST². These devices shipped with ALIGN® TRex helicopters are identical to MICROBEAST ULTRA. Just the labeling is different.

Additional features

AttitudeControl for recue bailout or constant leveling
Bank Switching which allows to change between different parameter presets in flight to serve different flight conditions or flying styles
Telemetry which transforms your MICROBEAST ULTRA into a hub for processing incoming and outgoing telemetry data

If you like, you can directly get the "ProEdition" upgrade. This unlocks all features at once at a fair pricing.

Technical specification:

wide input voltage range from 4 to 9 Volts
supports nearly all types of radio systems with conventional receiver wiring as well as lots of different serial signal receivers like SBUS, XBUS, EXBUS, iBus, UDI, SRXL, SRXL2, FRSky F.Port, SPPM, SUMD, Spektrum/JR/ALIGN remote satelites
preset swash plate mixing for mCCPM and 90, 120, 140 eCCPM + fully customizable swash mixing with up to 4 swash plate servos and virtual phasing for scale helicopters
swash plate servo update rate with up to 300Hz
integrated tail gyro with torque precompensation ("RevoMix") supports all types of rudder servos with 760, 960 and 1500(1520)µs pulse width and up to 560Hz update rate
integrated head speed governor for electric and nitro/gas driven helicopters (requires rpm sensor pickup or esc with rpm signal output)

Setup procedure
To setup MICROBEAST ULTRA there is no need for any additional devices. All you need is your radio system and your helicopter. Thanks to the well proven EasySetup system you can do all the necessary adjustment directly at the device and in very short time. If you like to get more insight into the system and like to have a more visualized type of setup you can also use the StudioX App for PC/Mac/Smartphone/Tablet in combination with USB2SYS or BLE2SYS interface (optional available). These apps are the source to get even more out of your device like saving/restoring paramaters, firmware updates, loading preset heli configurations and making advanced adjustment to fully customize MICROBEAST ULTRA to your needs.

Firmware version 5.5.x

Please note that these instructions are only valid for MICROBEAST ULTRA firmware version 5.5.x and above!

The firmware version can be detected by connecting your device with the StudioX App. Also you can directly read from the LED display of the device what firmware version it is running: After power up when the Status-LED lights in red color, for a few seconds the Menu-LEDs A to G display the first digit of the firmware version and the LEDs H to N indicate the second digit.