Line 38: |
Line 38: |
| * JETI® EXBUS | | * JETI® EXBUS |
| * GRAUPNER® HOTT | | * GRAUPNER® HOTT |
− | * FRSKY® F.Port2 | + | * FRSKY® F.Port |
| * FUTABA® SBUS2 | | * FUTABA® SBUS2 |
| <br /> | | <br /> |
Line 88: |
Line 88: |
| == Single wire with telemetry == <!--T:14--> | | == Single wire with telemetry == <!--T:14--> |
| Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2, FUTABA® SBUS2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br /> | | Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2, FUTABA® SBUS2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br /> |
| + | <br /> |
| + | When using a Futaba receiver with SBUS2 output, it is necessary to connect a 4.7kOhms resistor between signal pin and "-" (minus), so called pull-down resistor. You can make you own connection wire, if you have some skills in soldering. Otherwise please ask you local dealer if he can help out with such a modified wire.<br /> |
| + | <br /> |
| {|cellspacing="50" style="text-align:center;" | | {|cellspacing="50" style="text-align:center;" |
| |[[Image:SRXL2 AR6610T en.png| x150px]] | | |[[Image:SRXL2 AR6610T en.png| x150px]] |
Line 123: |
Line 126: |
| | | |
| == Single wire with telemetry == <!--T:19--> | | == Single wire with telemetry == <!--T:19--> |
− | When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to the '''[IO1]''' output. The telemetry data signal of the ESC is connected to '''[IO2]''' input. (You will get further information about connecting the speed controller in a later section!)<br /> | + | When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to the '''[IO1]''' output. The telemetry data signal of the ESC is connected to '''[IO2]''' input.<br /> |
| + | <br /> |
| + | Spektrum® AVIAN ESC do not have a separate line for telemetry data. Here motor control and telemetry data is sent bidirectional on the main connection wire. For this we must connect the AVIAN ESC to the [SYS] port of MICROBEAST ULTRA, as the other connectors [IO1] and [IO2] can only work in one direction.<br /> |
| + | <br /> |
| + | You will get further information about connecting and setting up the speed controller in a later section!<br /> |
| <br /> | | <br /> |
| | | |