Changes

* Im Sender den Servoweg vergrößern oder die Steuercharakteristik "Parameterpunkt B" eine Stufe höher stellen. Falls Expo per Sender dazugemischt werden soll, bitte Punkt B unbedingt auf "blau / Sender" stellen und dann mit reduziertem Servoweg langsam an die gewünschte Einstellung herantasten.

* Im Sender den Servoweg vergrößern oder die Steuercharakteristik "Parameterpunkt B" eine Stufe höher stellen. Falls Expo per Sender dazugemischt werden soll, bitte Punkt B unbedingt auf "blau / Sender" stellen und dann mit reduziertem Servoweg langsam an die gewünschte Einstellung herantasten.

The presets in parameter B are nothing else than different preset dualrate/expo curves inside the MB. When using these it is recommended not to change the output signal in the TX as especially when using expo this will bend, compress or stretch the curves leading to very strange flight behavior (it just is not like adding 5% of expo as the curves between TX and Microbeast will multiply and not sum together!) If you like the feeling of course you can do this. For example a slight increase in stick throw for increasing the roll rate will not significantly deform the Microbeast's internal curve and can be done with no problem. But easiest thing would be to switch flight behaviour to "blue=TX" and adjust the curves in your transmitter as you like (therefor I'd suggest to start with 70% D/R and 25% expo on cylic and 85% D/R and 40% expo on tail). When setting parameter B to "blue = TX" these internal curves in MB will be disabled. So 100% stick should give 100% rotation rate. This may vary depending on TX brand as any manufacturer use another signal output as maximum. So this can be at 107 or 110% or also at 95%. Manufacturers calculate expo curves different, so we can't tell you what our preset curves correspond to which TXs expo values as we use our own expo and there is no data available for comparing. We did outfly these values and programmed them in the source code so we can't tell what these are in Futaba or JR percentages.

: Die einzelnen Phasen bei Parametermenü Punkt B sind eine Mischung aus Expo und einer bestimmten Drehrate. Da die eingestellten Werte nicht zahlengenau auf die unterschiedlichen Sendertypen passen empfehlen wir, falls eine eigene Einstellung per Fernsteuerung bevorzugt wird, Parameterpunkt B auf "blau" zu stellen, im Sender mit ca. 20 - 30% Expo zu beginnen (mit negativem Vorzeichen bei Futaba) und den Servoweg auf ca. 70-80% zu reduzieren und sich dann allmählich an das gewünschte Steuerverhalten heranzutasten.

If parameter B is set to blue and the tail gain is switched to heading lock mode you can see by the status LED at which tail stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position it will start to flash. At this point the maximum gyro controlled rotation rate is reached. By increasing the stick throw any more the LED will go off. At this point the rate control is switched off and the tail will spin freely. Here the only limit is the maximum possible tail pitch throw and normaly the tail will spin ultra fast. This can be used for example for performaning tail slides or turns with very fast spinning tail. For normal flying around this is not recommended as you may accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven.

If parameter B is set to blue and the tail gain is switched to heading lock mode you can see by the status LED at which tail stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position it will start to flash. At this point the maximum gyro controlled rotation rate is reached. By increasing the stick throw any more the LED will go off. At this point the rate control is switched off and the tail will spin freely. Here the only limit is the maximum possible tail pitch throw and normaly the tail will spin ultra fast. This can be used for example for performaning tail slides or turns with very fast spinning tail. For normal flying around this is not recommended as you may accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven.