Changes

- Some ESC do not arm when the throttle value in the radio is too close to the motor starting position. When adjusting throttle endpoints at Governor setup menu point B this was intended, so the system does "know" at which point the motor starts and additionally the system can determine the throttle positions of the transmitter. Anyhow if this does not work with your ESC and it won't start there is no other option than increasing the throttle endpoints in the transmitter again (after the positions have been set at Governor menu points B and C!) just until the ESC will initialize. Anyhow MICROBEAST PLUS knows at which point the Motor will start as endpoint have been set before. But note that now the rpm setting will differ from the given table of the MICROBEAST PLUS ProEdition manual, as you stretched the throttle range of the transmitter. So the given percentages may not fit to the desired rpms and the percentage for autorotation bailout mode may change. Use Governor menu point D to check how MICROBEAST interprets your throttle curve values by watching the Status LED color in the different flight phases at menu point D.

- Some ESC do not arm when the throttle value in the radio is too close to the motor starting position. When adjusting throttle endpoints at Governor setup menu point B this was intended, so the system does "know" at which point the motor starts and additionally the system can determine the throttle positions of the transmitter. Anyhow if this does not work with your ESC and it won't start there is no other option than increasing the throttle endpoints in the transmitter again (after the positions have been set at Governor menu points B and C!) just until the ESC will initialize. Anyhow MICROBEAST PLUS knows at which point the Motor will start as endpoint have been set before. But note that now the rpm setting will differ from the given table of the MICROBEAST PLUS ProEdition manual, as you stretched the throttle range of the transmitter. So the given percentages may not fit to the desired rpms and the percentage for autorotation bailout mode may change. Use Governor menu point D to check how MICROBEAST interprets your throttle curve values by watching the Status LED color in the different flight phases at menu point D.

<br />

<br />

- If MICROBEAST PLUS does not get a valid signal from the receiver within 2 seconds it'll lock the throttle and set it to the throttle failsafe position. I.E. this can happen when the receiver does not bind to the transmitter signal immediately when powering up. With some systems this can take a few seconds or this can occur when the transmitter is positioned too close to the receiver. So if the ESC does not arm in this condition probably the throttle failsafe position is not set correctly. Please enter Receiver setup menu and reset the failsafe position at receiver menu point N.

- If MICROBEAST PLUS does not get a valid signal from the receiver within 2 seconds it'll lock the throttle and set it to the throttle failsafe position. I.E. this can happen when the receiver does not bind to the transmitter signal immediately when powering up. With some systems this can take a few seconds or this can occur when the transmitter is positioned too close to the receiver. So if the ESC does not arm in this condition probably the throttle failsafe position is not set correctly. Please enter Receiver setup menu and reset the failsafe position at receiver menu point N.<br />

Note: After performing adjustments at Receiver setup menu both the Governor and AttitudeControl will be disabled.

So when using one or both of these functions don't forget to enable them again at Parameter menu point L and Setup

{{QUOTE|Note: After performing adjustments at Receiver setup menu both the Governor and AttitudeControl will be disabled. So when using one or both of these functions don't forget to enable them again at Parameter menu point L and Setup menu Point N. Especially in respect to the Governor function watch out not to switch on throttle as long as the Governor function is disabled at Setup menu point N. Otherwise the motor will start to run very abruptly when switching to idle up as you have direct motor control from the transmitter.}}<br />

menu Point N. Especially in respect to the Governor function watch out not to switch on throttle as long as the

Governor function is disabled at Setup menu point N. Otherwise the motor will start to run very abruptly when

switching to idle up as you have direct motor control from the transmitter.<br />

===Nitro RPM Governor - When recovering from an autorotation using the autorotation bail out function the throttle increases up to nearly full throttle and stays there===

===Nitro RPM Governor - When recovering from an autorotation using the autorotation bail out function the throttle increases up to nearly full throttle and stays there===