Changes

* When taking off do not use too much cyclic input. Just let the motor come up to speed and then quickly give pitch input. Only when the helicopter is airborne the system can operate and control commands. If the helicopter sits on the ground, however, a stick input(= command to rotate the heli) would have no effect and the system would increase the cyclic pitch more and more desperately to perform a rotational movement. As soon as the helicopter will get "light" by increasing the collective pitch it will tip over abruptly. So always make sure that the swash is aligned straight during starting procedure!

* When taking off do not use too much cyclic input. Just let the motor come up to speed and then quickly give pitch input. Only when the helicopter is airborne the system can operate and control commands. If the helicopter sits on the ground, however, a stick input(= command to rotate the heli) would have no effect and the system would increase the cyclic pitch more and more desperately to perform a rotational movement. As soon as the helicopter will get "light" by increasing the collective pitch it will tip over abruptly. So always make sure that the swash is aligned straight during starting procedure!

* Tilting in flight: Remove the main rotor blades and let the helicopter run in all speeds on the ground (beware of the rotating parts!). Again the swash should move straight up and down when giving pitch inputs. If at a certain speed it starts to tilt in one direction and this will depend on the rotor speed then that is almost certainly a vibration problem which confuses the sensors in the Microbeast. Trying different adhesive pads might help (smoother or firmer mount) or installing the unit in another location. But especially in the electric helicopter that brings in most cases nothing and there certainly is an error somewhere on the helicopter.

Tilting in flight: Remove the main rotor blades and let the helicopter run in all speeds on the ground (beware of the rotating parts!). Again the swash should move straight up and down when giving pitch inputs. If at a certain speed it starts to tilt in one direction and this will depend on the rotor speed then that is almost certainly a vibration problem which confuses the sensors in the Microbeast. Trying different adhesive pads might help (smoother or firmer mount) or installing the unit in another location. But especially in the electric helicopter that brings in most cases nothing and there certainly is an error somewhere on the helicopter.

: This can be: slightly bent hub of the tail rotor, jammed or defective ball bearings, tail blades / tail rotor is not properly balanced, engine bell not balanced / comes at a certain speed to vibrate or motor bearings damaged making the motor shaft vibrate, slipped ball bearings in the torque tube tail drive system or installed in the wrong position, main gear wobbles / unbalanced; motor shaft bends and runs rough, ... actually everything that rotates on the helicopter can be the cause of such a vibration. On electric helicopter you normaly should not hear, feel or see any mayor vibration (no vibrating tail fin or skids). Then it should normally be possible to attach the Microbeast only with a very thin adhesive pad on electric helis. On nitro helis the situation can be slightly different as the motors do shake the more or less. This can lead to shaking of the Microbeast unit itself and will make the rotor pane wobble. So here trying different pads or a sandwich made of two pads and a metal plate may help to stabilize the unit better. Also the wiring can be the cause of such a shaking. But when the swash tilts as explained above the cause normaly is some very high frequent (abnormal) vibration and trying around with different kinds of gyro pads only disguises the real cause and may not help 100%.

: This can be: slightly bent hub of the tail rotor, jammed or defective ball bearings, tail blades / tail rotor is not properly balanced, engine bell not balanced / comes at a certain speed to vibrate or motor bearings damaged making the motor shaft vibrate, slipped ball bearings in the torque tube tail drive system or installed in the wrong position, main gear wobbles / unbalanced; motor shaft bends and runs rough, ... actually everything that rotates on the helicopter can be the cause of such a vibration. On electric helicopter you normaly should not hear, feel or see any mayor vibration (no vibrating tail fin or skids). Then it should normally be possible to attach the Microbeast only with a very thin adhesive pad on electric helis. On nitro helis the situation can be slightly different as the motors do shake the more or less. This can lead to shaking of the Microbeast unit itself and will make the rotor pane wobble. So here trying different pads or a sandwich made of two pads and a metal plate may help to stabilize the unit better. Also the wiring can be the cause of such a shaking. But when the swash tilts as explained above the cause normaly is some very high frequent (abnormal) vibration and trying around with different kinds of gyro pads only disguises the real cause and may not help 100%.