7,241
edits
Changes
Jump to navigation
Jump to search
Line 3:
Line 3: − + − MICROBEAST was the first product of BEASTX company. It is a flybarless unit that can be programmed without the need for a computer or external programming device. Its unique EasySetup makes it possible to program the system within a few minutes just by using the button on the unit and your transmitter. There are not many parameters to adjust as MICROBEAST can be used with nearly any RC helicopter model "out of the box".<br />+ − {|style="margin-left: none;"+ − |[[File:Microbeast.png|none|x150px]]+ − |[[File:Microbeast_PLUS.png|none|x120px]] − |} − + + + − + − =MICROBEAST PLUS vs. MICROBEAST PLUS HD=+ − + − Today's servos and especially so-called high voltage servos typically have a very high power consumption. When using Futaba BLS 451 servos for example these are very modest. Savöx 1258/Align DS610 are much more demanding - one alone taking up to 15Amps peak for the instance of a second. And for very extreme example take high voltage Savöx servos SB-2271SG HV. They demand up to 27Amps (1 Servo!) peak which you can see when measuring the power consumption with an oscilloscope. So besides using a good stable and high rated power supply you have to ensure proper supply of the servos with this power. But when only connecting one servo plug with power leads into the receiver this may be insufficient and cause a "bottle neck" in power flow. Also when the current must take a long way through the receiver, the wiring and the MICROBEAST, this will produce high resistance due to the connections in between and additional loss of voltage. There is no benefit if the power supply/BEC itself can deliver 20-25A when this amount of current is not able to flow to the consumers.<br /> − {|style="margin-left: 50px;"+ − |[[File:Plus_and_plusHD.png|none|x120px]]+ − |} − Now the idea behind MICROBEAST PLUS HD is to provide a power connection that allows for using thick power cables and directly connect these to the unit, close to the servos. So the voltage loss due to wiring and plug connection is reduced to a minimum. In general for helis with standard size servo you should always use MICROBEAST PLUS HD, because this will eliminate the "servo plug problem" as one important factor that may be critical in regards to the power supply. But also keep an eye on the design of your power supply in general. I.e. when using an ESC with only one BEC line there will no benefit of using the HD version as you already have a "bottle neck" at the power output. The small wire will not be able to transfer more than 5 Amps continuous current. Connecting this little wire to MICROBEAST's HD input will not help very much here. If on the other hand you have at least two or even three BEC lines then this can be different as you may solder the power wires from the BEC together to the MICROBEAST PLUS HD high power plug. Then you have a much lower contact resistance compared to only connect the wires using the standard servo plugs, which is a real benefit for providing a stable power supply. Ideally you have a BEC or receiver battery that already comes with thick power wires. Here it is ideal to use MICROBEAST PLUS HD. Also when using a separate receiver battery i. e. on nitro or gas helis using MICROBEAST PLUS HD is the ideal way to connect the battery to your RC system. In addition to the adequate connection plug here you have an integrated switch system for switching the heli on and off, so there is no need to buy an extra switch.<br />+ + + − {{QUOTE|In regards to software and functionality in general there is no difference between MICROBEAST PLUS and MICROBEAST PLUS HD! Both use the same firmware and you can buy and upgrade both devices to ProEdition firmware.}}+ + + + + + + + + − + − =MICROBEAST PLUS from ALIGN=+ − MICROBEAST PLUS devices included in ALIGN T-Rex kits come with Firmware Version 4.x.x or 5.x.x '''BASIC'''. You can upgrade/update/register and use these devices just like any other MICROBEAST PLUS. Only difference is that these devices are carrying the ALIGN logo on the housing.+ − {|style="margin-left: 10px;" − |[[File:Align_MBPlus.png|none|x120px]] − |}<br /> + + + − + − =Can I use MICROBEAST PLUS with a gasser heli, especially with RPM Governor and AttitudeControl?=+ − We did do several tests with gas powered helis and we do not see any restriction on this. Gas motors produce very low frequent vibrations which normally can be filtered by the gyro sensors very well. So you should be able to fly with MICROBEAST PLUS and use AttitudeControl without issues on gasser helis. Also the RPM Governor function can be used with gas motors. Only restriction is that a rpm sensor with digital sensor output (PWM) must be used for proper function. Analog sensors like the Futaba GV1 magnet sensor or StatorGator which are often installed on gasser helis can't be used.<br />+ + + + + − + − + − + − + + + + + + + − =Differences between firmware versions (changelog)=+ − Here you can see what has changed from one version to the preceeding version.<br />+ − <br />+ − + − ==MICROBEAST PLUS== − <br /> − − <br /> − − :* repaired Tailtrimm − :* modified gov slow rampup setting − :* removed cyclic revomix from presets Line 128:
Line 138: − − {{Navigationsleiste − |titel = '''Older versions''' − |align = left − |inhalt = Line 198:
Line 203: + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + − +
Updating to match new version of source page
<br />
<br />
=MICROBEAST vs. MICROBEAST PLUS=
=Differences between firmware versions (changelog)=
Here you can get info on what has changed from one version to the preceeding firmware version.<br />
<br />
<br />
==MICROBEAST ULTRA==
MICROBEAST PLUS is the successor of MICROBEAST and comes with new hardware components like more powerful microcontroller and more accurate gyro sensors. Due to these new capabilities MICROBEAST PLUS can be upgraded with lots of additional features like an artificial horizon for controlling the attitude (used for Bailout rescue, flight training and angular mode), a governor function for controlling the rotor headspeed of the helicopter as well as a Bank switch feature for adding several parameter sets to serve different flight conditions.<br />
<br />
<br />
'''5.8.3'''<br />
:''Telemetry/PROEDITION''
:* bugfix for Kontronik JIVE LV/HV and YGE Texy telemetry<br />
<br />
<br />
'''5.8.1'''<br />
:''Telemetry/PROEDITION''
''I intend to use the MICROBEAST PLUS on my 600/700 heli. Should I go with the HD version? What's the difference?''<br />
:* added telemetry input data processing for OMP 65A ESC (OMP M4 heli)<br />
<br />
<br />
<br />
<br />
==MICROBEAST PLUS==
<br />
<br />
'''5.8.3'''<br />
:''Telemetry/PROEDITION''
:* bugfix for Kontronik JIVE LV/HV and YGE Texy telemetry<br />
<br />
<br />
'''5.8.1'''<br />
:''Telemetry/PROEDITION''
:* added telemetry data processing for OMP 65A ESC (OMP M4 heli)<br />
<br />
<br />
'''5.7.0'''<br />
:''Telemetry (optional/PROEDITION)''
:* added telemetry data processing for YGE ESC(YGE TEXY protocol)
:* added telemetry data processing for Spektrum AVIAN Smart ESC (must be connected at SYS port)
:* added telemetry data input for Graupner HOTT receivers (telemetry line must be connected at SYS port)
:* capacity correction value now can be used in combination with any telemetry ESC if needed<br />
<br />
<br />
'''5.5.2'''<br />
:''Telemetry (optional/PROEDITION)''
:* added telemetry data processing for Scorpion Tribunus II 14-200 ESC<br />
<br />
<br />
'''5.5.1'''<br />
:''Telemetry (optional/PROEDITION)''
:* added telemetry data processing for Hobbywing Platinum V5 ESC<br />
<br />
<br />
'''5.4.0'''<br />
:''Telemetry (optional/PROEDITION)''
:* added SRXL2 and EXBUS telemetry output
:* added telemetry data processing for Hobbywing Platinum V4, Kontronik Jive/Kosmik and Scorpion Tribunus ESCs<br />
<br />
<br />
'''5.2.4'''<br />
:''AttitudeControl rescue (optional/PROEDITION)''
:* added option for automatic rescue deactivation when helicopter reaches level position
<br />
<br />
:''Setup''
=Is it possible to connect 4 swash plate servos to MICROBEAST / MICROBEAST PLUS?=
:* menu point ordering has changed in SETUP MENU ('''H''' = servo reverse, '''I''' = stick directions, '''J''' = servo trim, '''K''' = cyclic throw, '''L''' = collective, '''M''' = swash limit)!
'''Firmware Version 4.x.x and lower:''' No, 3 swashplate servos only.<br />
:* added swashplate trim option to the trim menu at SETUP MENU Point '''J'''
<br />
<br />
'''Firmware Version 5.x.x:''' Yes, you can use up to 4 swash servos when using a single line receiver, i.e. for large scale helicopters. In this case we recommend to connect the servo outputs to a separate power distribution system. The 4th servo (2nd elevator servo) is connected to CH7 output of the MICROBEAST PLUS (only signal out!). See manual for further informations.<br />
:''Receivers''
:* added SRXL2 receiver protocol, can be connected at white pin board on the side
:* added option to connect iBus remote receiver (comes with ALIGN T-Rex 300X)
:* made ready for telemtry support (coming soon..)
<br />
<br />
:''StudioX''
:* added help buttons to display help text only when needed
:* added screen stacks for adjustment buttons for clearer display layout on smartphones
<br />
<br />
{{Navigationsleiste
|titel = '''Older versions'''
|align = left
|inhalt =
{{WARNING_QUOTE|When updating from firmware 4.x.x or lower to Version 5.x.x you will loose all your settings. Please carefully read the Version 5 instruction manual and do the basic setup again.}}<br />
'''5.1.4'''<br />
'''5.1.2'''<br />
'''5.1.2'''<br />
:''Tail gyro''
:''Tail gyro''
* added event logging function to better understand what the system is doing during operation and to give more information for support team
* added event logging function to better understand what the system is doing during operation and to give more information for support team
<br />
<br />
'''4.2.0'''<br />
'''4.2.0'''<br />
:''Basic functionality''
:''Basic functionality''
* Improved receiver channel initialization
* Improved receiver channel initialization
* Improved tail gyro algorithm for Normal-Rate mode<br />
* Improved tail gyro algorithm for Normal-Rate mode<br />
<br />
<br />
=Differences between hardware=
==MICROBEAST ULTRA==
MICROBEAST ULTRA is the successor of MICROBEAST PLUS. This device is the quintessence of more than 10 years of development and expertise in stabilization systems for RC helicopters. It combines all the features of the previous BEASTX systems and is ready for the future with a modern ARM Cortex MPU with even more computing power and storage capacity. The system is equipped with with an ultra fast MCU and latest MEMS sensors for measuring the aircraft‘s rotational movement with unprecedented precision. Currently the functions are almost identical to MICROBEAST PLUS but this may change with future firmware updates. Please note that it is not possible to convert from Plus to Ultra as the differences are hardware-related!<br />
<br />
<br />
==MICROBEAST vs. MICROBEAST PLUS==
MICROBEAST was the first product of BEASTX company. It is a flybarless unit that can be programmed without the need for a computer or external programming device. Its unique EasySetup makes it possible to program the system within a few minutes just by using the button on the unit and your transmitter. There are not many parameters to adjust as MICROBEAST can be used with nearly any RC helicopter model "out of the box".<br />
<br />
{|style="margin-left: none;"
|[[File:Microbeast.png|none|x150px]]
|[[File:Microbeast_PLUS.png|none|x120px]]
|}
MICROBEAST PLUS is the successor of MICROBEAST and comes with new hardware components like more powerful microcontroller and more accurate gyro sensors. Due to these new capabilities MICROBEAST PLUS can be upgraded with lots of additional features like an artificial horizon for controlling the attitude (used for Bailout rescue, flight training and angular mode), a governor function for controlling the rotor headspeed of the helicopter as well as a Bank switch feature for adding several parameter sets to serve different flight conditions.<br />
<br />
<br />
<br />
==MICROBEAST PLUS vs. MICROBEAST PLUS HD==
''I intend to use the MICROBEAST PLUS on my 600/700 heli. Should I go with the HD version? What's the difference?''<br />
<br />
Today's servos and especially so-called high voltage servos typically have a very high power consumption. When using Futaba BLS 451 servos for example these are very modest. Savöx 1258/Align DS610 are much more demanding - one alone taking up to 15Amps peak for the instance of a second. And for very extreme example take high voltage Savöx servos SB-2271SG HV. They demand up to 27Amps (1 Servo!) peak which you can see when measuring the power consumption with an oscilloscope. So besides using a good stable and high rated power supply you have to ensure proper supply of the servos with this power. But when only connecting one servo plug with power leads into the receiver this may be insufficient and cause a "bottle neck" in power flow. Also when the current must take a long way through the receiver, the wiring and the MICROBEAST, this will produce high resistance due to the connections in between and additional loss of voltage. There is no benefit if the power supply/BEC itself can deliver 20-25A when this amount of current is not able to flow to the consumers.<br />
<br />
{|style="margin-left: 50px;"
|[[File:Plus_and_plusHD.png|none|x120px]]
|}
<br />
Now the idea behind MICROBEAST PLUS HD is to provide a power connection that allows for using thick power cables and directly connect these to the unit, close to the servos. So the voltage loss due to wiring and plug connection is reduced to a minimum. In general for helis with standard size servo you should always use MICROBEAST PLUS HD, because this will eliminate the "servo plug problem" as one important factor that may be critical in regards to the power supply. But also keep an eye on the design of your power supply in general. I.e. when using an ESC with only one BEC line there will no benefit of using the HD version as you already have a "bottle neck" at the power output. The small wire will not be able to transfer more than 5 Amps continuous current. Connecting this little wire to MICROBEAST's HD input will not help very much here. If on the other hand you have at least two or even three BEC lines then this can be different as you may solder the power wires from the BEC together to the MICROBEAST PLUS HD high power plug. Then you have a much lower contact resistance compared to only connect the wires using the standard servo plugs, which is a real benefit for providing a stable power supply. Ideally you have a BEC or receiver battery that already comes with thick power wires. Here it is ideal to use MICROBEAST PLUS HD. Also when using a separate receiver battery i. e. on nitro or gas helis using MICROBEAST PLUS HD is the ideal way to connect the battery to your RC system. In addition to the adequate connection plug here you have an integrated switch system for switching the heli on and off, so there is no need to buy an extra switch.<br />
<br />
{{QUOTE|In regards to software and functionality in general there is no difference between MICROBEAST PLUS and MICROBEAST PLUS HD! Both use the same firmware and you can buy and upgrade both devices to ProEdition firmware.}}
<br />
<br />
==MICROBEAST PLUS from ALIGN==
MICROBEAST PLUS devices included in ALIGN T-Rex kits come with Firmware Version 4.x.x or 5.x.x '''BASIC'''. You can upgrade/update/register and use these devices just like any other MICROBEAST PLUS. Only difference is that these devices are carrying the ALIGN logo on the housing.
{|style="margin-left: 10px;"
|[[File:Align_MBPlus.png|none|x120px]]
|}<br />
<br />
<br />
=Questions about specific features=
==Can I use MICROBEAST PLUS with a gasser heli?==
''Especially is it possible to use the head speed governor and rescue (AttitudeControl)?''
We did do several tests with gas powered helis and we do not see any restriction on this. Gas motors produce very low frequent vibrations which normally can be filtered by the gyro sensors very well. So you should be able to fly with MICROBEAST PLUS and use AttitudeControl without issues on gasser helis. Also the governor function can be used with gas motors. Only restriction is that a speed sensor with digital sensor output (PWM) must be used for proper function. Analog sensors like the Futaba GV1 magnet sensor or StatorGator (which are often installed on gasser helis) can't be used.<br />
<br />
<br />
==Is it possible to connect 4 swash plate servos?==
'''Firmware Version 4.x.x and lower:''' No, 3 swashplate servos only.<br />
<br />
'''Firmware Version 5.x.x:''' Yes, you can use up to 4 swash servos when using a single line receiver, i.e. for large scale helicopters. In this case we recommend to connect the servo outputs to a separate power distribution system. The 4th servo (2nd elevator servo) is connected to CH7 output of the MICROBEAST PLUS (only signal out!). See manual for further informations.<br />
<br />
<br />
=Questions regarding support=
=My MICROBEAST / MICROBEAST PLUS is defective, where can I send it?=
==My MICROBEAST / MICROBEAST PLUS is defective, where can I send it?==
When you have an ALIGN branded device you could ask your ALIGN dealer for service or replacement. Other than that please ask your local BEASTX distributor for your country. Usually the distributors will replace your device, collect some more defective devices and then get new devices from us in exchange. Another option is to send the device directly to our service center in Germany, but when living outside Europe this can take a long time, as the parcels usually go to customs authorities first. When sending to the service center use [http://www.freakware.de/rma/rma-eng.pdf this RMA form], you will also find the shipping address there.<br />
When you have an ALIGN branded device you could ask your ALIGN dealer for service or replacement. Other than that please ask your local BEASTX distributor for your country. Usually the distributors will replace your device, collect some more defective devices and then get new devices from us in exchange. Another option is to send the device directly to our service center in Germany, but when living outside Europe this can take a long time, as the parcels usually go to customs authorities first. When sending to the service center use [http://www.freakware.de/rma/rma-eng.pdf this RMA form], you will also find the shipping address there.<br />
<br />
<br />
<br />
<br />