Bureaucrats, Administrators, translate-proofr
15,502
edits
Changes
Jump to navigation
Jump to search
Line 4:
Line 4: − + Line 32:
Line 32: − + + + + + Line 40:
Line 44: − + +
no edit summary
<translate>
<translate>
=Installation= <!--T:15-->
=Installation (Windows version)= <!--T:15-->
<br />
<br />
''I'm sure I have selected the correct interface port but StudioX scans for some time and than says no device found.''
''I'm sure I have selected the correct interface port but StudioX scans for some time and than says no device found.''
* Make sure the wiring is connected correctly. The servo wire coming from the USB interface goes into SYS port on your MICROBEAST PLUS / AR7210BX. Watch out for correct polarity and '''make sure that the device is powered from a receiver battery or BEC''' (only when using the RX2SIM interface the BEASTX device can be powered from the USB port!).
* Make sure the wiring is connected correctly. The servo wire coming from the USB interface goes into SYS port on your MICROBEAST PLUS / AR7210BX. Watch out for correct polarity and '''make sure that the device is powered from a receiver battery or BEC''' (only when using the RX2SIM interface the BEASTX device can be powered from the USB port!).
* When using a smartphone the BLE2SYS interface must be connected to the SYS port, watch out for correct polarity. Make sure the LED on the BLE2SYS flashes in intervals of 2 seconds. By default the interface deactivates after 30 seconds when there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.<br />
* When using a smartphone the BLE2SYS interface must be connected to the SYS port, watch out for correct polarity. Make sure the LED on the BLE2SYS flashes in intervals of 2 seconds. By default the interface deactivates after 30 seconds when there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.
* When LED on BLE2SYS is flashing repeatedly in short intervals the device is locked due to wrong pin code. Also in this case, power cycle and try again.
* Keep some distance between smartphone and bluetooth device (apprx. 30cm or 1 ft). When both devices are too close, the bluetooth connection can be interupted.
* Make sure there are no other devices around that can interfere with the 2,4GHz bluetooth connection. I.e. power off your radio transmitter or make sure to keep it at bigger distance to the helicopter. There have been reports that radio systems can interfer with the bluetooth connection when devices are on the work bench altogether!<br />
<br />
<br />
Usually when you click "Connect" button, the LED on the BLE2SYS must light up solid blue and data transfer should be displayed in the Studiox app. When LED goes off and you get the message "No device found", power off everything and again check for proper connection between BLE2SYS and MICROBEAST SYS port. Completely close the StudioX app (on iPhone double tap Home button and swipe StudioX app away, on Android hold menu button and swipe app away). Then power on Microbeast and BLE2SYS. Start StudioX app again and try again. Ideally BLE2SYS should be selected already in the menu bar, so just click "Connect" button immediately when app opens.<br />
<br />
<br />
* Do NOT connect to the BLE2SYS device using the bluetooth menu of your smartphone/tablet, StudioXm will establish connection by itself!
* Do NOT connect to the BLE2SYS device using the bluetooth menu of your smartphone/tablet, StudioXm will establish connection by itself!
* BLE2SYS uses bluetooth smart (bluetooth LE), make sure your mobile device supports this specific bluetooth protocol.
* BLE2SYS uses bluetooth smart (bluetooth LE), make sure your mobile device supports this specific bluetooth protocol.
* Make sure the LED on the BLE2SYS flashes in intervals of 2 seconds. By default the interface deactivates after 30 seconds whe there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.<br />
* Make sure the LED on the BLE2SYS flashes in intervals of 2 seconds. By default the interface deactivates after 30 seconds whe there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.
* Click "Rescan" to start searching for bluetooth device in StudioX. Usually you should see some device called "BLE2SYS". But the name can be different especially when you've bought a used device from someone else. There can be other devices with long numbers like "Unknown{(12345....)}". Do not try to connect to those, these are different bluetooth devices around that can't be indentified.<br />
<br />
<br />
<br />
<br />