7,261
edits
Changes
Jump to navigation
Jump to search
Importing a new version from external source
{{DISPLAYTITLE:SETUP MENU B - Swashplate frequency|noerror}}
{{TOC_AR7210V5|Manuals:AR7210FblV5:Setupmenu_A/en|Manuals:AR7210FblV5:Setupmenu_C/en|SETUPMENU}}
__TOC__
<br />
Setup menu point '''B''' is for selecting the servo update frequency (pulse rate) of the swashplate servos. To optimize the flight performance of AR7210BX the rule is: the higher the better! With high update frequency the system will recalculate correctional movements more often and in consequence will send new commands to the servos with a higher frequency. Nevertheless, this will cause the servos to make more position changes at a given timeframe. In case your servo is not built for this kind of application this can cause an unusual high power consumption of the receiver power supply and cause the servos getting very hot. When this happens, reduce frequency immediately to prevent your servos from getting damaged. Only go as high as recommended by the servo manufacturer, or even lower when the servo is not capable of handling such high frequency in field use.<br />
<br />
When using a servo that allows a higher frequency as AR7210BX offers or that allows a maximum frequency which is not choosable, please select the next lower frequency that is closest to the given frequency or set the frequency with StudioXm PC Software or mobile App. '''Note:''' Using a lower frequency is always possible. Only too high frequencies can damage the servo and/or will cause the servo to not work properly. [[The_BEASTX_servo_list/en|Here]] you can find a list of parameters for the most common servos. Please understand that we can not list all servo types. We also can not guarantee the accuracy of this data. Ask the manufacturer of the servos or your servo dealer for detailed information.<br />
<br />
{{QUOTE|[[Image:Warning.png|18px|sub]] '''If you do not know the maximum pulse rate tolerated by your servos do not select more than 50Hz driving frequency.''' A higher driving frequency can lead to failure of the servos!<br />
With high frequencies, some servos run in a jerky manner, especially the fast ones with coreless or brushless servos. This is due to the high update rate that the servo receives. This is not critical and will not impact flight performance.}}<br />
<br />
=Adjustment on the device=
To select the desired servo frequency move the rudder stick repeatedly in one direction until the Status-LED lights in the correct color at SETUP MENU point B:<br />
<br />
{{TABLEV5|Swashplate servo frequency|50 Hz|65 Hz|120 Hz|165 Hz|200 Hz}}<br />
'''Note:''' When you set a different frequency using the StudioXm App the Status LED will be '''off'''. You can change back to a preset setting by tapping the rudder stick as described, but this will remove your custom setting!<br />
<br />
<br />
=Setup with StudioXm=
Choose a preset frequency by clicking one of the provided buttons for Menu Point B (Swashplate frequency) or set a custom frequency by directly changing the value with the dial or buttons.<br />
<br />
[[File:SetupB_mobile.png|x250px]]<br />
<br />
<br />
=Servo connection=
'''After setting the correct update frequency plug in the swashplate servos, but do not install the servo horns yet as the servos could bind and get damaged on first power up!'''<br />
<br />
{|class="gallery"
| style="padding:0px 0px;" align="center" | [[Image:Swashtypes.png|x100px|none|border]]
<!-- | style="padding:0px 40px;" align="center" | [[Image:Swashservo_connection.png|x100px|none]] -->
|}
<br />
<br />
With electronic swashplate mixing the two aileron servos have to be connected to CH2 (=left) and CH3 (=right). With a mechanical mixed head (H1) the aileron servo connects to CH2 and collective pitch servo to CH3. Plug the the elevator servo into CH1 port. When using a scale helicopter with 90 degrees eCCPM you can connect a second elevator servo to AUX3 output on the AR7210BX.<br />
<br />
{{QUOTE|When you route the wire leads in your model make sure that there is no tension passed to the AR7210BX. Make sure that the receiver is able to move freely, so no vibrations get passed onto the unit by the wire leads. It is not recommended to bundle or tie down the leads close to the AR7210BX. On the other hand the wires must be attached so that they are unable to move the AR7210BX during the flight caused by g-force. In particular, do not use any shrink tubing or fabric hose to bundle or encase the wiring in close proximity to the point at which the cables are plugged into the AR7210BX. This makes the cables stiff and inflexible and can cause vibrations being transmitted to AR7210BX.}}<br />
<br />
<br />
{{TOC_AR7210V5|Manuals:AR7210FblV5:Setupmenu_A/en|Manuals:AR7210FblV5:Setupmenu_C/en|SETUPMENU}}
__TOC__
<br />
Setup menu point '''B''' is for selecting the servo update frequency (pulse rate) of the swashplate servos. To optimize the flight performance of AR7210BX the rule is: the higher the better! With high update frequency the system will recalculate correctional movements more often and in consequence will send new commands to the servos with a higher frequency. Nevertheless, this will cause the servos to make more position changes at a given timeframe. In case your servo is not built for this kind of application this can cause an unusual high power consumption of the receiver power supply and cause the servos getting very hot. When this happens, reduce frequency immediately to prevent your servos from getting damaged. Only go as high as recommended by the servo manufacturer, or even lower when the servo is not capable of handling such high frequency in field use.<br />
<br />
When using a servo that allows a higher frequency as AR7210BX offers or that allows a maximum frequency which is not choosable, please select the next lower frequency that is closest to the given frequency or set the frequency with StudioXm PC Software or mobile App. '''Note:''' Using a lower frequency is always possible. Only too high frequencies can damage the servo and/or will cause the servo to not work properly. [[The_BEASTX_servo_list/en|Here]] you can find a list of parameters for the most common servos. Please understand that we can not list all servo types. We also can not guarantee the accuracy of this data. Ask the manufacturer of the servos or your servo dealer for detailed information.<br />
<br />
{{QUOTE|[[Image:Warning.png|18px|sub]] '''If you do not know the maximum pulse rate tolerated by your servos do not select more than 50Hz driving frequency.''' A higher driving frequency can lead to failure of the servos!<br />
With high frequencies, some servos run in a jerky manner, especially the fast ones with coreless or brushless servos. This is due to the high update rate that the servo receives. This is not critical and will not impact flight performance.}}<br />
<br />
=Adjustment on the device=
To select the desired servo frequency move the rudder stick repeatedly in one direction until the Status-LED lights in the correct color at SETUP MENU point B:<br />
<br />
{{TABLEV5|Swashplate servo frequency|50 Hz|65 Hz|120 Hz|165 Hz|200 Hz}}<br />
'''Note:''' When you set a different frequency using the StudioXm App the Status LED will be '''off'''. You can change back to a preset setting by tapping the rudder stick as described, but this will remove your custom setting!<br />
<br />
<br />
=Setup with StudioXm=
Choose a preset frequency by clicking one of the provided buttons for Menu Point B (Swashplate frequency) or set a custom frequency by directly changing the value with the dial or buttons.<br />
<br />
[[File:SetupB_mobile.png|x250px]]<br />
<br />
<br />
=Servo connection=
'''After setting the correct update frequency plug in the swashplate servos, but do not install the servo horns yet as the servos could bind and get damaged on first power up!'''<br />
<br />
{|class="gallery"
| style="padding:0px 0px;" align="center" | [[Image:Swashtypes.png|x100px|none|border]]
<!-- | style="padding:0px 40px;" align="center" | [[Image:Swashservo_connection.png|x100px|none]] -->
|}
<br />
<br />
With electronic swashplate mixing the two aileron servos have to be connected to CH2 (=left) and CH3 (=right). With a mechanical mixed head (H1) the aileron servo connects to CH2 and collective pitch servo to CH3. Plug the the elevator servo into CH1 port. When using a scale helicopter with 90 degrees eCCPM you can connect a second elevator servo to AUX3 output on the AR7210BX.<br />
<br />
{{QUOTE|When you route the wire leads in your model make sure that there is no tension passed to the AR7210BX. Make sure that the receiver is able to move freely, so no vibrations get passed onto the unit by the wire leads. It is not recommended to bundle or tie down the leads close to the AR7210BX. On the other hand the wires must be attached so that they are unable to move the AR7210BX during the flight caused by g-force. In particular, do not use any shrink tubing or fabric hose to bundle or encase the wiring in close proximity to the point at which the cables are plugged into the AR7210BX. This makes the cables stiff and inflexible and can cause vibrations being transmitted to AR7210BX.}}<br />
<br />
<br />