Line 24: |
Line 24: |
| <br /> | | <br /> |
| | | |
− | For bi-directional telemetry connect the SRXL2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST PLUS / ULTRA. When using the DI2 port an adapter from standard servo connector to 5-pin JST is required as shown below. Or you can use the original 4-pin wire that comes with your SPEKTRUM® receiver. In this case please note the the wire must be modified as shown below! | + | For bi-directional telemetry connect the SRXL2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST PLUS / ULTRA. When using the DI2 port an adapter from standard servo connector to 5-pin JST is required as shown below. Or you can use the original 4-pin wire that comes with your SPEKTRUM® receiver. In this case please note the the wire must be modified as shown below!<br /> |
| + | <br /> |
| + | |
| + | ==Connecting to SYS port== |
| + | (Picture MICROBEAST)<br /> |
| + | <br /> |
| + | |
| + | (Picture Nanobeast)<br /> |
| + | <br /> |
| | | |
| + | ==Connecting to DI2 port== |
| To connect a receiver with standard servo connectors, i.e. the '''AR6610T''' or '''AR8020T''' you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br /> | | To connect a receiver with standard servo connectors, i.e. the '''AR6610T''' or '''AR8020T''' you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br /> |
| <br /> | | <br /> |
Line 33: |
Line 42: |
| | SRXL2 receiver with standard servo connector and adapter | | | SRXL2 receiver with standard servo connector and adapter |
| |} | | |} |
− | <br />
| |
| <br /> | | <br /> |
| | | |
Line 48: |
Line 56: |
| <br /> | | <br /> |
| | | |
− | | + | == Throttle servo / ESC == |
− | (Picture Nanobeast)<br />
| |
− | <br />
| |
− | | |
| '''MICROBEAST PLUS'''<br /> | | '''MICROBEAST PLUS'''<br /> |
− | The ESC or throttle servo is connected at DI1 port. If needed the telemetry data line from the ESC is connected to the CH5 port.<br /> | + | The ESC or throttle servo usually is connected at DI1 port. If needed the telemetry data line from the ESC is connected to the CH5 port.<br /> |
| <br /> | | <br /> |
| + | When using a SPEKTRUM® Avian ESC with SRXL2 telemetry this must be connected at SYS port. In consequence it is mandatory to connect the receiver at the DI2 port as shown above!<br /> |
| <br /> | | <br /> |
| | | |
Line 60: |
Line 66: |
| The ESC or throttle servo is connected at IO1 port. If needed the telemetry data line from the ESC is connected to the IO2 port.<br /> | | The ESC or throttle servo is connected at IO1 port. If needed the telemetry data line from the ESC is connected to the IO2 port.<br /> |
| <br /> | | <br /> |
| + | When using a SPEKTRUM® Avian ESC with SRXL2 telemetry this must be connected at SYS port. In consequence it is mandatory to connect the receiver at the DI2 port as shown above!<br /> |
| <br /> | | <br /> |
| | | |
| '''NANOBEAST'''<br /> | | '''NANOBEAST'''<br /> |
− | The ESC or throttle servo is connected at CH5 port. If needed the telemetry data line from the ESC is connected to the SAT port.<br /> | + | The ESC or throttle servo is connected at CH1 port. If needed the telemetry data line from the ESC is connected to the SAT port.<br /> |
| + | <br /> |
| + | Using a SPEKTRUM® Avian ESC is only possible in standard PWM mode connected at CH1 port. As NANOBEAST does not have enough bi-directional ports available, it is not possible to use the SRXL2 telemetry backlink here.<br /> |
| <br /> | | <br /> |
| <br /> | | <br /> |