Übersicht zum SETUPMENÜ

Hier findest Du eine Übersicht und eine kurze Beschreibung zur Ersteinrichtung im SETUPMENÜ. Weitere Details zu den einzelnen Einstellschritten findest Du in den folgenden Unterabschnitten.

Beim MICROBEAST PLUS / ULTRA wird der aktuelle Menüschritt durch die gelben LEDs neben den Buchstaben signalisiert. Im SETUPMENÜ muss die Menü LED dauerhaft leuchten. Wenn die LEDs blinken, dann bist Du im falschen Menü!

Bei NANOBEAST wird der aktuelle Menüschritt durch die Anzahl der Blinksignale der Status LED angezeigt. Im SETUPMENÜ blinkt die Status LED hierbei blau. Die Schritte A bis G werden durch 1 bis 7 Blinkzeichen angezeigt. Ab den Schritten H bis M blinkt die LED wiederum 1 bis 7 Mal. Aber hier wird aber das erste Blinkzeichen lang sein.

SETUPMENÜ Übersicht

Menü	Beschreibung	aus	blinkt violett	violett	blinkt rot	rot	blinkt blau	blau	abwechselnd rot/blau
A	Einbaulage	flach, Anschl. vorn	hochkant, Anschl. vorn	kopfüber, Anschl. vorn	hochkant kopfüber, Anschl. vorn	flach, Anschl. hinten	hochkant, Anschl. hinten	kopfüber, Anschl. hinten	hochkant kopfüber, Anschl. hinten
B	Servo Frequenz	Benutzer		50 Hz	65 Hz	120 Hz	165 Hz	200 Hz
C	Heck Pulsweite	Benutzer		760 µs		960 µs		1520 µs
D	Heck Frequenz	Benutzer		50 Hz	165 Hz	270 Hz	333 Hz	560 Hz
E	Heck Limit					Limit links		Limit rechts
F	Heck Richtung					links		rechts
G	Taumelscheibe	Benutzer		mechanisch	90°(3/4 servos)	120°	140°	135°/140°(1:1)
H	Servo Richtungen			Servo 1		Servo 2		Servo 3	(Servo 4)
I	Steuerrichtungen					links / zurück		rechts / vorwärts
J	Servomitten	neutral		Servo 1		Servo 2		Servo 3	(Servo 4)
K	Steuerweg	Neutral		zu wenig		OK		Super!
L	Pitch					min		MAX
M	Servo Limit			zu viel		OK		Super!
N	Governor	aus				Elektro		Verbrenner

A - Einbaulage

Tap rudder stick to select device orientation (change LED color). Please be very careful when choosing the orientation. A wrong orientation will cause the system to move the heli in the wrong direction!

B - Servo Frequenz

Tap rudder stick to select frequency (change LED color). Most digital servos can be used with 200Hz.

Warning: If frequency is too high you can burn the servo!

C - Heck Pulsweite

Tap rudder stick to select pulse width (change LED color). Most servos run at 1520µs (or 1500µs which is nearly the same!). Special gyro servos use 760µs pulse. Usually this will be printed on the servo.

D - Heck Frequenz

Tap rudder stick to select frequency (change LED color). Most digital rudder servos can be used with 333Hz. Special gyro servos with 760µs pulse can go even higher.

Warning: If frequency is too high you can burn the servo!

E - Heck Limit

Use rudder stick (hold or tap) to move servo to one endpoint. Wait until LED flashes, then move all the way to the other endpoint. Wait again until LED flashes. If stick direction is inverted, use servo reverse function on radio to reverse direction.

Helicopters with tail motor

When using the firmware with tail motor support, here you can set stop position of the tail motor. Tap or hold rudder stick to adjust output signal for tail motor ESC.

Turn on the main throttle on the radio to start the tail motor. Now you can adjust the lowest possible running position for the tail motor using the rudder stick again. Set the motor speed to a low idle position just before the motor will quit. Then turn off main throttle and proceed to next step.

F - Heck Richtung

1. Move rudder left/right. Servo should move tail left/right accordingly. If stick direction is inverted, use servo reverse function on radio to reverse direction.

2. Check LED color: right = blue and left = red. If LED color is incorrect, tap aileron/roll stick once to reverse LED color. Don't use reverse function on radio to change LED color!

Helicopters with tail motor

1. Move rudder left/right and check LED color: right = blue and left = red. If LED color is incorrect, tap aileron/roll stick once to reverse LED color. Don't use reverse function on radio to change LED color!

2. Turn on the main throttle on the radio to start the tail motor. Now you can adjust the start and hovering position for the tail motor. Tap or hold the the rudder stick and set the motor to a medium speed that will give a little push to the right, but not too much so the heli won't turn on the ground. Then turn off main throttle and proceed to next step.

G - Taumelscheibe

Tap rudder stick to select swash plate type and swash mixing (change LED color). Most R/C helis use 120° eCCPM mixing. Check your heli's manual for more details.

H - Servo Richtungen

Tap rudder stick to select one servo after another. Move collective pitch on the radio and check servo directions. All servos must move the swash plate vertically together. If necessary, tap the roll/aileron stick once to reverse the direction of the selected servo. Repeat this for all servos.

Note: When the heli uses mechanical mixing (mCCPM) menu step H is not accessible and will be skipped.

I - Steuerrichtungen

1. Move roll/aileron to the right and push pitch/elevator forwards. Check cyclic swashplate movement. The swash should move forwards and right as well. If direction is wrong, use servo reverse function on the radio and reverse roll or pitch channel as needed.

2. Check LED color: Pushing the sticks forward and right, Status LED must light blue. Backwards and left is must be red. If LED color is incorrect, tap rudder stick once to reverse LED color. There are 4 possible options, only one can be correct. Don't use reverse function on radio to change LED color!

J - Servomitten

Tap rudder stick to select one servo after another. If necessary, tap/hold the roll/aileron stick to adjust the servo center position. All servos should form a 90 degrees angle to the linkages. The swashplate must be perfectly level. Repeat this for all servos.

Note: When the Status LED is off, all servos are in their true center position (1520µs pulse width).

K - Zykl. Steuerweg

Status LED off: Make sure blade pitch is 0.0° and swashplate is level.

Tap rudder stick to switch to adjustment position. Here tap or hold aileron/roll stick to adjust cyclic pitch to exact 6.0°.

L - Pitch

1. Move thrust/collective stick and check directions. If servos are moving the swashplate in wrong direction, use servo reverse function on radio to invert thrust/colelctive channel.

2. Check LED color: Positive pitch = blue, negative pitch = red. Tap rudder stick once to inverse color if needed.

3. Move thrust/collective stick on the radio to lowest position. Here tap or hold aileron/roll stick to adjust pitch as needed, i.e. -12.0 degrees.

4. Move thrust/collective stick on the radio to highest position. Here tap or hold aileron/roll stick to adjust pitch as needed, i.e. +12.0 degrees.

M - Servo Limit

Move thrust/collective stick on the radio to highest position. Carefully push cyclics (roll/aileron and pitch/elevator) to end positions. Check if servos or linkages are binding. If needed, tap or hold rudder stick to adjust limit.

Move thrust/collective stick on the radio to lowest position. Carefully push cyclics (roll/aileron and pitch/elevator) to end positions. Check if servos or linkages are binding. If needed, tap or hold rudder stick to adjust limit.

Again check all possible swashplate positions if there is still any binding and adjust as needed. Please note that limit value will affect all positions. So you must find the position where binding happens first and adjust limit there.

N - Drehzahlregler (Governor)

Tap rudder stick to select governor mode (change LED color). When not using the internal governor feature (Status LED off), setup will end here. When using electric or nitro governor, next menu step will be step A of GOVERNOR MENU.

Note: Governor feature is only available for MICROBEAST PLUS / ULTRA at the moment.