Bureaucrats, Administrators, translate-proofr
15,502
edits
Changes
Jump to navigation
Jump to search
Line 2:
Line 2: − + Line 54:
Line 54: − + Line 116:
Line 116: − + + + + + + + + + + + + + + + + + + + +
Manuals:MBPlusFblV52:Radio System (view source)
Revision as of 12:56, 25 September 2020
, 3 years agono edit summary
<translate>
<translate>
<!--T:1-->
<!--T:1-->
{{TOC_MBPlusV5|Manuals:MBPlusFblV52:Hardware_Installation/en|Manuals:MBPlusFblV52:ReceiverType/en2}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV52:Hardware_Installation/en|Manuals:MBPlusFblV52:ReceiverType/en||2}}
{{DISPLAYTITLE:Radio system|noerror}}
{{DISPLAYTITLE:Radio system|noerror}}
__TOC__
__TOC__
=Receiver installation= <!--T:3-->
=Receiver installation= <!--T:3-->
MICROBEAST PLUS can work with a lot of different receiver types and radio brands and especially with different types of signal protocols. Depending on which signal protocol you intend to use for controlling the MICROBEAST PLUS the wiring layout may vary. In the following you can see all supported protocols and specific wiring scheme for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />
MICROBEAST PLUS can work with a lot of different receiver types and radio brands and especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />
<br />
<br />
<br />
<br />
==Receiver binding== <!--T:7-->
==Spektrum® SRXL2 receiver== <!--T:6-->
Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as remote satellites with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS. '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />
<br />
In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter
BXA76401 but this requires to modify the wiring layout as shown below!<br />
<br />
In order to connect a SRXL2 remote satelite like SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
<br />
{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
<br />
{|cellspacing="20" style="text-align:center;"
|[[Image:Mbplus_spektrum_rx2.png | x100px]]
|- style="text-align:center; font-size:75%;"
| JR®/Spektrum® remote satellite connected at side pin board
|}<br />
<br />
When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
<br />
=Receiver binding= <!--T:7-->
<p>
<p>
Before using your receiver with MICROBEAST PLUS make sure that the receiver is bound to the transmitter and that it is sending output data on the servo outputs and/or single-line port. Please refer to the manual of your radio system to find out how binding procedure is performed with your specific system. Also check if there is the need to perform special settings to enable the single-line data output of the receiver in case you intend to use this output port in combination with MICROBEAST PLUS.</p>
Before using your receiver with MICROBEAST PLUS make sure that the receiver is bound to the transmitter and that it is sending output data on the servo outputs and/or single-line port. Please refer to the manual of your radio system to find out how binding procedure is performed with your specific system. Also check if there is the need to perform special settings to enable the single-line data output of the receiver in case you intend to use this output port in combination with MICROBEAST PLUS.</p>