Changes

<!--T:11-->

<!--T:11-->

MICROBEAST PLUS can work with a lot of different receiver types and radio brands and especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />

MICROBEAST PLUS can work with a lot of different receiver types and radio brands and especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />

<br />

<br />

* You must connect all 5 functions/wires to the receiver. When you do not connect all wires the system will not finish initialization sequence!

* You must connect all 5 functions/wires to the receiver. When you do not connect all wires the system will not finish initialization sequence!

* The throttle servo/speed controller is connected to the receiver's throttle output. Using the Governor function of MICROBEAST PLUS therefore is not possible in combination with a Standard receiver.}}<br />

* The throttle servo/speed controller is connected to the receiver's throttle output. Using the Governor function of MICROBEAST PLUS therefore is not possible in combination with a Standard receiver.}}<br />

<br />

<br />

| Wiring layout for single-line receivers

| Wiring layout for single-line receivers

| Alternative wiring layout for single-line receiver<br /> with additional servo output channels

| Alternative wiring layout for single-line receiver<br /> with additional servo output channels

|}<br />

|}

<br />

<br />

<!--T:10-->

<!--T:10-->

'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Note when only connecting power at the receiver, all the current has to flow over one thin wire to the servos! If there are no other ports left to (additionally) feed in power, we highly recommend using the MICROBEAST PLUS HD which has an additional high power input to reduce wiring resistance and to serve todays demands for a robust servo power supply.<br />

'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Note when only connecting power at the receiver, all the current has to flow over one thin wire to the servos! If there are no other ports left to (additionally) feed in power, we highly recommend using the MICROBEAST PLUS HD which has an additional high power input to reduce wiring resistance and to serve todays demands for a robust servo power supply.<br />

<br />

<br />

| JR®/Spektrum® remote satellite connected at side pin board

| JR®/Spektrum® remote satellite connected at side pin board

| JR®/Spektrum® remote satellite connection with power adapter

| JR®/Spektrum® remote satellite connection with power adapter

|}<br />

|}

<br />

<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input to receiver and servos. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port.<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input to receiver and servos. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port.<br />

<br />

<br />

{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc modells like helicopters of 450 size or smaller.''' Due to the design one single receiving unit is more prone to radio interference and can result in reduced transmission range.}}<br />

{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc modells like helicopters of 450 size or smaller.''' Due to the design one single receiving unit is more prone to radio interference and can result in reduced transmission range.}}<br />

<br />

<br />

=Spektrum® SRXL2 receiver= <!--T:7-->

=Spektrum® SRXL2 receiver= <!--T:7-->

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as remote satellites with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS. '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as remote satellites with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />

<br />

<br />

In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter

In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!<br />

BXA76401 but this requires to modify the wiring layout as shown below!<br />

<br />

<br />

In order to connect a SRXL2 remote satellite like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />

In order to connect a SRXL2 remote satellite like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 Satellite en.png| x180px]]

|[[Image:SRXL2 Satellite en.png| x180px]]

|- style="text-align:center; font-size:75%;"

|- style="text-align:center; font-size:75%;"

| AR6610T receiver with standard servo connector

| SRXL2 satellite receiver with modified satellite connector

| SRXL2 satellite receiver with modified connector

|}

|[[Image:SRXL2 Satellite correct en.png| x120px]]

|}<br />

|}<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />

{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />

<br />

<br />

<br />

</translate>

</translate>