Changes

<br />

<br />

=Receivers with single wire output (single-line receivers)=

=Receivers with single wire output=

A single-line receiver transmits all channels (control functions) by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a digital data paket or by chaining the servo signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />

A single-line receiver transmits all channels/all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all stick outputs to a digital data paket or by chaining the signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBUS, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM.<br />

 

{{QUOTE|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-wire layout as shown above, such receiver has to be considered as "Standard receiver".}}<br />

(For Spektrum® SRXL2 or when you like to make use of telemetry data, please connect your receiver as shonw under [[#Spektrum® SRXL2 / JETI EXBUS receivers for telemetry]].)<br />

<br />

<br />

* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS

* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS

* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.

* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.

* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.

* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.<br />

{|cellspacing="20" style="text-align:center;"

{|cellspacing="20" style="text-align:center;"

|[[Image:Singleline_RX_3.png | x150px]]

|[[Image:Singleline_RX_3.png | x150px]]

|- style="text-align:center; font-size:75%;"

|- style="text-align:center; font-size:75%;"

| Wiring layout for single-line receivers

| Single-line receiver<br /> with additional servo output channels

| Alternative wiring layout for single-line receiver<br /> with additional servo output channels

|}

|}

<br />

<br />

<br />

<br />

=Spektrum® SRXL2 receiver=

=Telemetry receivers Spektrum® SRXL2 / JETI EXBUS=

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. Anyways, the output signal of those receiver must always be connected to the pin board at the side of MICROBEAST PLUS.<br />

'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />

<br />

<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />

Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />

<br />

<br />

<br />

<br />

In order to connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />

To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 AR6610T en.png| x150px]]

|[[Image:SRXL2 AR6610T en.png| x150px]]

| SRXL2 receiver with standard servo connector and adapter

| SRXL2 receiver with standard servo connector and adapter

|}

|}

In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 Satellite en.png| x180px]]

|[[Image:SRXL2 Satellite en.png| x180px]]

|- style="text-align:center; font-size:75%;"

|- style="text-align:center; font-size:75%;"

| SRXL2 satellite receiver with modified satellite connector

| SRXL2 satellite receiver with modified satellite connector

|}

|}

{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />

{{WARNING_QUOTE|'''Never connect the 4-pin receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />

<br />

|}<br />

<br />

<br />