7,261
edits
Changes
Jump to navigation
Jump to search
Line 4:
Line 4: − <p>Due to the possibility of connecting very different types of receivers with different types of signal output, you must setup the receiver type in the RECEIVER MENU. Additionally when using a single-line receiver it is mandatory to define the function assignment for the receiver output channels. A single-line receiver bundles the control information to data packages or serialized electical signals. So by default it is not clear, which channel controls which (stick) function. Finally when using a single-line receiver you have to set a failsafe position for the throttle channel. This defines at which position the motor is disabled and where to move the throttle in case the receiver is not sending any throttle signal, i.e. during power up or in case of loss of radio link.</p>+ + + + + + + Line 11:
Line 17: + + Line 31:
Line 39: − Line 166:
Line 173: + + + + + + +
Manuals:MBPlusFblV52:ReceiverType/en (view source)
Revision as of 12:50, 30 March 2022
, 2 years agoUpdating to match new version of source page
<br />
<br />
You can use nearly any radio system in combination with MICROBEAST PLUS. Due to the very different types of receivers with different types of signal output, you must setup the receiver type in the RECEIVER MENU.<br />
<br />
Additionally when using a single-line receiver it is mandatory to define the function assignment for the receiver output channels. A single-line receiver bundles the control information to data packages or serialized electrical signals. So by default it is not clear, which channel controls which (stick) function.<br />
<br />
Since firmware version 5.4.x it is also possible to use a telemetry ESC. MICROBEAST PLUS processes the telemetry data and forwards it to the receiver. Again, there is a huge variety on the market and lots of different types of protocols are used. So it is necessary to setup the telemetry type as well, before you can use MICROBEAST PLUS with your radio system.<br />
<br />
Finally when using a single-line receiver you have to set a failsafe position for the throttle channel. This defines at which position the motor is disabled and where to move the throttle in case the receiver is not sending any throttle signal, i.e. during power up or in case of loss of radio link.<br />
<br />
<br />
{{QUOTE|By default the "Standard Receiver" is selected as receiver type. So if you're using this type of receiver and your MICROBEAST PLUS is brand new, you can skip this section as it is already setup correctly!}}<br />
{{QUOTE|By default the "Standard Receiver" is selected as receiver type. So if you're using this type of receiver and your MICROBEAST PLUS is brand new, you can skip this section as it is already setup correctly!}}<br />
=Preset function assignments for Single-line receivers=
=Preset function assignments for Single-line receivers=
When using a single line receiver please note the preset function assignment below and check whether functions are setup in a similar ways on your radio system (i.e. check your stick monitor on the radio). When your assignements are different, you can teach your assignment to MICROBEAST PLUS at RECEIVER MENU Point B and following.<br />
<br />
'''Spektrum® remote satelite or SRXL/SRXL2 receiver'''
'''Spektrum® remote satelite or SRXL/SRXL2 receiver'''
|}</p>
|}</p>
<br />
<br />
'''PPM serial signal (SPPM)'''
'''PPM serial signal (SPPM)'''
<br />
<br />
{{QUOTE|If the Status-LED lights in '''red color''' this means either there is no valid remote control signal available or that you did try to assign two or more channels to a function. So check if the receiver is connected and powered properly and that you're only moving one channel at a time when trying to do the manual function assignment.}}<br />
{{QUOTE|If the Status-LED lights in '''red color''' this means either there is no valid remote control signal available or that you did try to assign two or more channels to a function. So check if the receiver is connected and powered properly and that you're only moving one channel at a time when trying to do the manual function assignment.}}<br />
<br />
==Point M - Telemetry==
''This feature was added with MICROBEAST PLUS firmware 5.4.x and can be purchased as optional feature (included in ProEdition).''<br />
<br />
UNDER CONSTRUCTION --- coming soon!!!<br />
<br />
<br />
<br />