7,261
edits
Changes
Jump to navigation
Jump to search
Line 12:
Line 12: + Line 42:
Line 43: − + Line 80:
Line 81: − + Line 124:
Line 125: + + + + + + +
Manuals:MBPlusFblV52:Receiver M/en (view source)
Revision as of 07:24, 18 August 2023
, 8 months agoUpdating to match new version of source page
* Kontronik® JIVE Pro/Kosmik
* Kontronik® JIVE Pro/Kosmik
* YGE® ESC with Texy protocol
* YGE® ESC with Texy protocol
* OMP 65A ESC that is included with OMP M4 heli
* Scorpion® Tribunus II ("UnSc" mode)
* Scorpion® Tribunus II ("UnSc" mode)
* Spektrum Avian ESC (connected at [SYS] port)
* Spektrum Avian ESC (connected at [SYS] port)
|-
|-
|style="color:white; background-color:#CC66CC" | purple
|style="color:white; background-color:#CC66CC" | purple
| Hobbywing® Platinum V5
| Hobbywing® Platinum V5 / OMP 65A ESC
|-
|-
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
Connect the control wire of your Hobbywing® ESC to port [DI1]. Connect the programming port of your Hobbywing® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />
Connect the control wire of your Hobbywing® ESC to port [DI1]. Connect the programming port of your Hobbywing® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />
<br />
<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST PLUS. The motor speed signal can be used for the internal governor function of MICROBEAST PLUS. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
If needed you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS. The motor speed signal can be used for the internal governor function of MICROBEAST PLUS. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
<br />
<br />
<br />
<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />
<br />
<br />
==OMP 65A ESC==
Connect the control wire of your OMP ESC to port [DI1]. Connect the pin labeled with "TX" from the ESC to the port [CH5] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
<br />
Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST PLUS will convert the data into your radio's protocol as needed.
<br />
<br />
<br />
<br />