Changes

107 bytes added , 6 years ago

Importing a new version from external source

Line 1: Line 1:

__NOTOC__

−

+

{{TOC_MBPlusV5|Manuals:MBPlusFblV5:Hardware_Installation/en|Manuals:MBPlusFblV5:ReceiverType/en}}

__TOC__

Line 48: Line 48:

{{QUOTE|[[File:Warning.png|18px|sub]] '''Make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and MICROBEAST PLUS disconnect the motor from the ESC.}}

+

Line 55: Line 56:

==Standard receiver==

−

A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each servo output to one specific control function at the MICROBEAST PLUS using one connection wire for each function. You have these 5 input functions (wires): Aileron, Elevator, Rudder, Collective pitch and gyro gain. Simply connect each wire to the corresponding channel output port at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!

+

A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each servo output to one specific control function at the MICROBEAST PLUS using one connection wire for each function. You have these 5 input functions (wires): Aileron, Elevator, Rudder, Collective pitch and gyro gain. Simply connect each wire to the corresponding channel output port at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!

{|cellspacing = "20"

|style="text-align:center;"| [[Image:Standard_RX.png|250px]]

−

|}

+

|}

Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any other radio system on the market together with MICROBEAST PLUS when using the servo output channels of the receiver, not only these two brands!

{|cellspacing = "20"

|[[Image:Spektrum_RX.png|x100px]]

|[[Image:Futaba_RX.png|x100px]]

−

|}

+

|}

{{QUOTE|

* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!

Line 89: Line 90:

−

'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Note when only connecting power at the receiver, all the current has to flow over one thin wire to the servos! If there are no other ports left to (additionally) feed in power, we highly recommend using the MICROBEAST PLUS HD which has an additional high power input to reduce wiring resistance and to serve todays demands for a robust servo power supply.

+

'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Note when only connecting power at the receiver, all the current has to flow over one thin wire to the servos! If there are no other ports left to (additionally) feed in power, we highly recommend using the MICROBEAST PLUS HD which has an additional high power input to reduce wiring resistance and to serve todays demands for a robust servo power supply.

+

==Spektrum® DSM/JR® DMSS remote satellite==

Line 109: Line 111:

−

===Receiver binding===

+

==Receiver binding==

Before using your receiver with MICROBEAST PLUS make sure that the receiver is bound to the transmitter and that it is sending output data on the servo outputs and/or single-line port. Please refer to the manual of your radio system to find out how binding procedure is performed with your specific system. Also check if there is the need to perform special settings to enable the single-line data output of the receiver in case you intend to use this output port in combination with MICROBEAST PLUS.

−

Only in the case of using a single Spektrum® remote satellite receiver directly connected to MICROBEAST PLUS you must bind the receiver by the aid of MICROBEAST PLUS as there is no other option to enable binding procedure at the receiver. ~~Even more, here~~ '''it is very important to bind the receiver first before programming MICROBEAST PLUS and this step must be performed, even if the satellite was already in use and already bound to the transmitter earlier''' (e. g. in connection with a Spektrum® main receiver unit).

+

Only in the case of using a single Spektrum® remote satellite receiver directly connected to MICROBEAST PLUS you must bind the receiver by the aid of MICROBEAST PLUS as there is no other option to enable binding procedure at the receiver. '''Please note that it is very important to bind the receiver first before programming MICROBEAST PLUS and this step must be performed, even if the satellite was already in use and already bound to the transmitter earlier''' (e. g. in connection with a Spektrum® main receiver unit).

{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}

Line 120: Line 122:

When initiating bind sequence you have to set whether you're using a DSMX or DSM2 satellite (the actual selected signal protocol in the transmitter is not relevant!). '''It is very important to choose the correct type of satellite receiver here, since an improper setting may seem to work but can lead to radio interference or total loss of radio linkage in the subsequent operation!'''

−

Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST PLUS. In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5]. To ~~bin~~ a '''DSMX''' satellite simply switch on the power supply now. The LED on the receiver and LED '''H''' on MICROBEAST PLUS will start to flash. You can bind the transmitter as usual (for more information refer to the instructions of your radio control system). To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST PLUS while switching on the power supply. Now the receiver‘s LED and LED '''N''' (!) on the MICROBEAST PLUS will flash. Release the button and bind the receiver with your transmitter.

+

Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST PLUS. In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5]. To bind a '''DSMX''' satellite simply switch on the power supply now. The LED on the receiver and LED '''H''' on MICROBEAST PLUS will start to flash. You can bind the transmitter as usual (for more information refer to the instructions of your radio control system). To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST PLUS while switching on the power supply. Now the receiver‘s LED and LED '''N''' (!) on the MICROBEAST PLUS will flash. Release the button and bind the receiver with your transmitter.

After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST PLUS will enter receiver setup menu automatically as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.

{|cellspacing="20"

−

|[[File:~~Spektrum_bind~~.png|~~x500px~~]]

+

|[[File:Spektrum_bind_v5.png|x400px]]

|}

FuzzyBot

7,261

edits

Changes

Manuals:MBPlusFblV5:Radio System/en (view source)

Revision as of 17:37, 11 January 2018

Navigation menu

Search