Changes

{{DISPLAYTITLE:SETUP MENU (Basic heli setup)|noerror}}

{{DISPLAYTITLE:SETUP MENU (Basic heli setup)|noerror}}

__TOC__

__TOC__

<br />

<br />

<br />

<br />

=Basic setup with StudioX=

=Basic setup with StudioXm=

When StudioX is started and your MICROBEAST PLUS was detected by StudioX click the Basic Setup tab to show the adjustment options of SETUP MENU. The options you see here are basically similar to the Menu Points you can change directly at the device. There might be little differences because of the different nature of the computer setup. Wait until the system has initialized completely (if not the setup options will not be accessible!). Then if you like you can click the '''Wizard button''' on top of the options table. This will guide you from Menu Points A to N (M when governor function is not provided). When you've finished one adjustment step, always click the '''Next button''' at each step to proceed to the next option. It is not a must to use the '''Wizard button''' and you can setup each menu point of your choice independent from each other, but it is advisable to use the '''Wizard button''' so you don't miss any setup step. Also note the Menu Points sometimes build on each other, so adjusting some points without doing the preceeding steps is not useful!<br />

<p>When StudioXm is started and your MICROBEAST PLUS is connected to StudioXm choose '''Basic heli setup''' from the device overview page to enter the setup wizard, which will lead through the basic setup procedure of the SETUP MENU (note that the menu is only accessible after all settings have been loaded from the device and when the device is in operation mode! See [[StudioXm/en|general informations about StudioXm]] if you need further instructions). The options you see here are basically similar to the SETUP MENU points A to M you can change directly at the device, but there might be little differences because of the different nature of the interactive setup. The adjustment is basically done using the buttons or dials in the app, sometimes interaction with your transmitter is necessary. Click '''Next''' at the bottom of each setup step to skip to the following Menu Point. From the dropdown list at the top also you can directly access specific setup items if necessary, but for the first time setup it is recommended to proceed step-by-step beginning at ''Device Orientation'' and ending with ''Cyclic directions''. Adjustment procedure in short words is described at each step. If necessary refer to this manual if you need further assistance. When the setup is finished click the '''Home button''' in the top left corner to get back to the overview screen or disconnect the device and deactivate the BLE2SYS module by clicking the '''Disconnect button''' in the top right corner when adjustment is finished completely.</p>

<br />

<br />

'''Note:''' When you cannot access the menu options because the system does not finish initialization sequence, make sure the radio system is powered up and bound correctly and proceed with [[Manuals:MBPlusFblV5:ReceiverType/en|RECEIVER MENU adjustment]] first, if necessary!<br />

'''Note:''' When you cannot access the menu options because the system does not finish initialization sequence, make sure the radio system is powered up and bound correctly and proceed with [[Manuals:MBPlusFblV5:ReceiverType/en|RECEIVER MENU adjustment]] first, if necessary!<br />

<br />

<br />

<br />

<br />

 

'''Also make sure MICROBEAST PLUS is in operation mode!''' When it is still in one of the adjustment menus the gyro control and the stick controls may be disabled and you will not be able to fully control your helicopter!}}<br />

{{WARNING_QUOTE|'''Always disconnect your BLE2SYS from the app when you attempt to fly in order to deactivate the module or disconnect it physically from your MICROBEAST PLUS.''' When the module is active this can cause interference with your radio system as the BLE2SYS is also sending on the 2.4GHz band! '''Also make sure MICROBEAST PLUS is in operation mode!''' When it is still in one of the adjustment menus the gyro control and the stick controls may be disabled and you will not be able to fully control your helicopter!}}<br />