7,261
edits
Changes
Jump to navigation
Jump to search
Line 47:
Line 47: − <br /> Line 56:
Line 55: + − '''Binding procedure for Spektrum® remote satellites''' + − + − + − <br /> − To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br /> − <br /> − + + − {|cellspacing="20" − |[[File:Spektrum_bind_v5.png|x400px]] − |}
Manuals:MBUltraFblV5:Radio Setup/en (view source)
Revision as of 10:37, 6 November 2023
, 6 months agoUpdating to match new version of source page
</p>
</p>
{{QUOTE|[[File:Warning.png|18px|sub]] '''Make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and MICROBEAST ULTRA disconnect the motor from the ESC.}}<br />
{{QUOTE|[[File:Warning.png|18px|sub]] '''Make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and MICROBEAST ULTRA disconnect the motor from the ESC.}}<br />
<br />
<br />
In case of using a single Spektrum® remote DSM2/DSMX satellite receiver directly connected to MICROBEAST ULTRA, you must bind the receiver by the aid of MICROBEAST ULTRA. Here we have no other option to enable binding procedure at the receiver. '''Please note that it is very important to bind the receiver first before programming MICROBEAST ULTRA and this step must be performed, even if the satellite was already in use and already bound to the transmitter earlier''' (e. g. in connection with a Spektrum® main receiver unit).</p>
In case of using a single Spektrum® remote DSM2/DSMX satellite receiver directly connected to MICROBEAST ULTRA, you must bind the receiver by the aid of MICROBEAST ULTRA. Here we have no other option to enable binding procedure at the receiver. '''Please note that it is very important to bind the receiver first before programming MICROBEAST ULTRA and this step must be performed, even if the satellite was already in use and already bound to the transmitter earlier''' (e. g. in connection with a Spektrum® main receiver unit).</p>
<p> </p>
<p> </p>
<br />
=Bind procedure Spektrum® DSMX satellite=
<p>
<p>
* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
* Disconnect(!) the Spektrum® remote satellite.
* Disconnect(!) the Spektrum® remote satellite (this is different to previous MICROBEAST and MICROBEAST PLUS devices!)
* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br />
* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br />
<br />
<br />
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}<br />
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}
<br />
<br />
To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br />
* To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br />
* To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br />
<br />
<br />
After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>
After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>
<p>
<p>
'''Note:'''
'''Note:'''