Bureaucrats, Administrators, translate-proofr
15,511
edits
Changes
Jump to navigation
Jump to search
Line 31:
Line 31: − + Line 37:
Line 37: + − + Line 48:
Line 49: − Receivers without telemetry and with a standard servo wire connector are plugged into the [IO1] input of MICROBEAST ULTRA.<br />+ + + + + Line 70:
Line 75: − <br /> − − The throttle servo or ESC is connected to the [IO2] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos! Additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit. '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended!<br /> − + + Line 83:
Line 86: − + Line 95:
Line 98: − + − + + +
no edit summary
=Receivers with single wire output= <!--T:5-->
=Receivers with single wire output= <!--T:5-->
A single-line receiver transmits all channels/all control functions over one single connection wire to MICROBEAST ULTRA . This is done by packing all stick outputs to a digital data paket or by chaining the signals.<br />
A single-line receiver transmits all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all channel outputs into a digital data paket or by chaining the signals onto one line.<br />
MICROBEAST ULTRA supports the following systems '''with telemetry uplink''':
MICROBEAST ULTRA supports the following systems '''with telemetry uplink''':
* Spektrum® SRXL2
* Spektrum® SRXL2
* GRAUPNER® HOTT
* GRAUPNER® HOTT
* FRSKY® F.Port2
* FRSKY® F.Port2
* FUTABA® SBUS2
<br />
<br />
MICROBEAST ULTRA supports the following systems '''without telemetry''':
MICROBEAST ULTRA supports the following systems '''without telemetry''':
* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output
* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output
* Futaba® SBus (SBusI)
* Futaba® SBUS
* Multiplex® SRXL
* Multiplex® SRXL
* JR® X-Bus (Mode B)
* JR® X-Bus (Mode B)
<br />
<br />
== Single wire without telemetry ==
* The single-line connection wire is plugged into the [IO1] input of MICROBEAST ULTRA
* The throttle servo or ESC is connected to the [IO2] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD|PIT|AUX]; please do not connect anything here!).<br />
<br />
<br />
<br />
{|cellspacing="20" style="text-align:center;"
{|cellspacing="20" style="text-align:center;"
<br />
<br />
{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc models (helicopters of 450 size or smaller).''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range!}}<br />
{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc models (helicopters of 450 size or smaller).''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range!}}<br />
<br />
<br />
<br />
<br />
Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
== Single wire with telemetry ==
Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2, FUTABA® SBUS2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
{|cellspacing="50" style="text-align:center;"
{|cellspacing="50" style="text-align:center;"
|[[Image:SRXL2 AR6610T en.png| x150px]]
|[[Image:SRXL2 AR6610T en.png| x150px]]
|}
|}
<br />
<br />
<br />
To connect a SRXL2 remote receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
To connect a SRXL2 remote receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
{|cellspacing="50" style="text-align:center;"
{|cellspacing="50" style="text-align:center;"
<br />
<br />
<br />
<br />
* When telemetry is not in use, the throttle servo or ESC is connected to the '''[IO2]''' output.
When using a telemetry receiver and an ESC with telemtry data connector, the ESC is connected to the [IO1] output. The data signal of the ESC is connected to [IO2] input. (You will get further information about connecting the speed controller and setting up telemetry on the next page!) When using a speed controller with BEC, from here the power will be distributed to receiver and servos! Additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit. '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended!<br />
* When using a telemetry receiver and an ESC with telemtry data connector, the ESC is connected to the '''[IO1]''' output. The data signal of the ESC is connected to '''[IO2]''' input. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD|PIT|AUX]; please do not connect anything here!).<br />
<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
<br />
<br />
<br />
<br />
</translate>
</translate>