Bureaucrats, Administrators, translate-proofr
15,511
edits
Changes
Jump to navigation
Jump to search
Line 38:
Line 38: − + Line 88:
Line 88: + Line 125:
Line 126: − + + + + +
no edit summary
* JETI® EXBUS
* JETI® EXBUS
* GRAUPNER® HOTT
* GRAUPNER® HOTT
* FRSKY® F.Port2
* FRSKY® F.Port
* FUTABA® SBUS2
* FUTABA® SBUS2
<br />
<br />
== Single wire with telemetry == <!--T:14-->
== Single wire with telemetry == <!--T:14-->
Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2, FUTABA® SBUS2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
Receivers with bidirectional telemetry uplink (Spektrum® SRXL2, Jeti® EXBUS, FRSKY® F.Port2, FUTABA® SBUS2) must be connected to the pin board at the side of MICROBEAST ULTRA. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
<br />
When using a Futaba receiver with SBUS2 output, it is necessary to connect a 4.7kOhms resistor between signal pin and "-" (minus), so called pull-down resistor. You can make you own connection wire, if you have some skills in soldering. Otherwise please ask you local dealer if he can help out with such a modified wire.<br />
When using a Futaba receiver with SBUS2 output, it is necessary to connect a 4.7kOhms resistor between signal pin and "-" (minus), so called pull-down resistor. You can make you own connection wire, if you have some skills in soldering. Otherwise please ask you local dealer if he can help out with such a modified wire.<br />
<br />
<br />
== Single wire with telemetry == <!--T:19-->
== Single wire with telemetry == <!--T:19-->
When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to the '''[IO1]''' output. The telemetry data signal of the ESC is connected to '''[IO2]''' input. (You will get further information about connecting the speed controller in a later section!)<br />
When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to the '''[IO1]''' output. The telemetry data signal of the ESC is connected to '''[IO2]''' input.<br />
<br />
Spektrum® AVIAN ESC do not have a separate line for telemetry data. Here motor control and telemetry data is sent bidirectional on the main connection wire. For this we must connect the AVIAN ESC to the [SYS] port of MICROBEAST ULTRA, as the other connectors [IO1] and [IO2] can only work in one direction.<br />
<br />
You will get further information about connecting and setting up the speed controller in a later section!<br />
<br />
<br />