7,261
edits
Changes
Jump to navigation
Jump to search
Line 6:
Line 6: + Line 15:
Line 16: + Line 63:
Line 65: − + Line 98:
Line 100: − + Line 144:
Line 146: + + + + + + +
Manuals:MBUltraFblV5:Receiver M/de (view source)
Revision as of 07:22, 18 August 2023
, 8 months agoUpdating to match new version of source page
<br />
<br />
<div class="mw-translate-fuzzy">
'''Folgende Motorsteller/Sensoren werden derzeit unterstützt:'''
'''Folgende Motorsteller/Sensoren werden derzeit unterstützt:'''
* Hobbywing® Platinum (V4/V5)
* Hobbywing® Platinum (V4/V5)
* Drehzahlsensor (am RPM Anschluß)<br />
* Drehzahlsensor (am RPM Anschluß)<br />
<br />
<br />
</div>
'''Folgende Fernsteuersysteme können für die Telemetrieübertragung verwendet werden:'''
'''Folgende Fernsteuersysteme können für die Telemetrieübertragung verwendet werden:'''
|-
|-
|style="color:white; background-color:#CC66CC" | purple
|style="color:white; background-color:#CC66CC" | purple
| Hobbywing® Platinum V5
| Hobbywing® Platinum V5 / OMP 65A ESC
|-
|-
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
==Hobbywing® Platinum (V4/V5)==
==Hobbywing® Platinum (V4/V5)==
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO3] using a standard servo wire with male servo plugs on each end.<br />
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO2] using a standard servo wire with male servo plugs on each end.<br />
<br />
<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
<br />
<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
<br />
<br />
==OMP 65A ESC==
Connect the control wire of your OMP ESC to port [IO1]. Connect the pin labeled with "TX" from the ESC to the port [IO2] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST ULTRA, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
<br />
Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST ULTRA will convert the data into your radio's protocol as needed.
<br />
<br />
<br />
<br />