7,261
edits
Changes
Jump to navigation
Jump to search
Line 11:
Line 11: + + − + Line 63:
Line 65: − + Line 70:
Line 72: + + + Line 95:
Line 100: − + Line 102:
Line 107: − + + Line 141:
Line 147: + + + + + + +
Manuals:MBUltraFblV5:Receiver M/en (view source)
Revision as of 08:15, 12 September 2023
, 8 months agoUpdating to match new version of source page
* Kontronik® JIVE/PowerJIVE/HeliJIVE
* Kontronik® JIVE/PowerJIVE/HeliJIVE
* Kontronik® JIVE Pro/Kosmik
* Kontronik® JIVE Pro/Kosmik
* YGE® ESC with Texy protocol
* OMP 65A ESC that is included with OMP M4 heli
* Scorpion® Tribunus II ("UnSc" mode)
* Scorpion® Tribunus II ("UnSc" mode)
* Spektrum Avian ESC (connected at [SYS] port)
* Spektrum® Avian ESC (connected at [SYS] port)
* Speed sensor (connected at [RPM] input)<br />
* Speed sensor (connected at [RPM] input)<br />
<br />
<br />
|-
|-
|style="color:white; background-color:#CC66CC" | purple
|style="color:white; background-color:#CC66CC" | purple
| Hobbywing® Platinum V5
| Hobbywing® Platinum V5 / OMP 65A ESC
|-
|-
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background-color:#FF3300" | red
|style="color:white; background-color:#FF3300" | red
| Kontronik® JIVE Pro/Kosmik
| Kontronik® JIVE Pro/Kosmik
|-
|style="color:white; background: linear-gradient(to right, #0066FF, black, #0066FF)" | blue flashing
| YGE® Texy
|-
|-
|style="color:white; background-color:#0066FF" | blue
|style="color:white; background-color:#0066FF" | blue
==Hobbywing® Platinum (V4/V5)==
==Hobbywing® Platinum (V4/V5)==
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO3] using a standard servo wire with male servo plugs on each end.<br />
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO2] using a standard servo wire with male servo plugs on each end.<br />
<br />
<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
[[File:Hobbywing.png|x300px|none]]
[[File:Hobbywing.png|x300px|none]]
<br />
<br />
{{QUOTE|* Smaller Hobbywing® Platinum models (Platinum 60 and 80) do not measure current. Here displayed current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.
{{QUOTE|* There are some Hobbywing® Platinum models (i. e. Platinum "LV" series) that do not measure current. Here current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.
* Additionally some ESC do not measure temperature, so Temperature will stay at 0 degrees in your telemetry display. It's no malfunction, there simply is no value available.
* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ULTRA. Then you can display motor speed/headspeed on your radio at least!}}<br />
* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ULTRA. Then you can display motor speed/headspeed on your radio at least!}}<br />
<br />
<br />
<br />
<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
<br />
<br />
==OMP 65A ESC==
Connect the control wire of your OMP ESC to port [IO1]. Connect the pin labeled with "TX" from the ESC to the port [IO2] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST ULTRA, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
<br />
Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST ULTRA will convert the data into your radio's protocol as needed.<br />
<br />
<br />
<br />
<br />