Changes

<br />

<br />

<span style="font-size: 13px;">&#42;&#42;AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls ''CH6 Output''.<br /></span>

<span style="font-size: 13px;">&#42;&#42;AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls ''CH6 Output''.<br /></span>

<span style="font-size: 13px;">&#42;&#42;&#42;Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span>

<span style="font-size: 13px;">&#42;&#42;&#42;Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span><br />

<br />

<br />

To load the preset channel assignment wait until the Status-LED lights blue and then hold down the button for several seconds. The yellow Menu-LED will immediately jump to [[Manuals:MB_Plus:Receiver_setup_A|Receiver menu point '''N''']].<br />

To load the preset channel assignment wait until the Status-LED lights <font color="#0066FF">'''blue'''</font> and then hold down the button for several seconds. The yellow Menu-LED will immediately jump to [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''N''']].<br />

<br />

<br />

[[File:Channel_assignment.png|x200px|none]]

[[File:Channel_assignment.png|x200px|none]]

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.<br />

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.<br />

<br />

<br />

{{QUOTE|* If the Status-LED stays red at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

{{QUOTE|* If the Status-LED stays <font color="#FF3300">'''red'''</font> at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point N]] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point L]]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}<br />

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point N]] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point L]]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}<br />

<br />

<br />