Changes

{{QUOTE|* If the Status-LED stays '''red''' at menu point '''B''', this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

{{QUOTE|* If the Status-LED stays '''red''' at menu point '''B''', this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}</p>

* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}</p>

===Teaching of customized channel order=== <!--T:3-->

===Teaching of customized channel order=== <!--T:3-->

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.</p>

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.</p>

<p>&nbsp;</p>

<p>&nbsp;</p>

{{QUOTE|* If the Status-LED stays '''red''' at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

{{QUOTE|* If the Status-LED stays '''red''' at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point '''N''']] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point '''L''']]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}</p>

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point '''N''']] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point '''L''']]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}

<p>

<p>

----

----