Changes

{{TOC_MBPlus}}

{{TOC_MBPlus}}

{{DISPLAYTITLE:Receiver setup menu point B and following|noerror}}

{{DISPLAYTITLE:Receiver setup menu point B and following|noerror}}

If not a standard receiver but a single-line receiver was selected at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']], it must be established which control function is controlled by what channel. This is necessary because all the control functions are transmitted via one single line and virtually every manufacturer uses his own order in the arrangement of channels to control functions. There is no possibility of plugging the cables in each individual channel matching, like it is with a standard receiver.<br />

<br />

If not a standard receiver but a single-line receiver was selected at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']], it must be established which control function is controlled by what channel. This is necessary because all the control functions are transmitted via one single line and virtually every manufacturer uses his own order in the arrangement of channels to control functions. There is no possibility of plugging the cables in each individual channel matching, like it is with a standard receiver.</p>

===Preset channel assignment===

===Preset channel assignment===

<p>For each specific type of single-line receiver selected at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']] there is an appropriate type of receiver channel allocation saved in MICROBEAST PLUS. Please refer to the tables below. Use the column that represents your receiver type and the Status-LED color that was set at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']] and check if your radio transmits the channels in the defined order respectively each stick function on the radio is transmitted using the specified channel number on the left. To know the channel assignment of your transmitter you can check the user manual of the transmitter or look at the servo monitor of the transmitter if it has this feature. If in doubt ask the manufacturer of your transmitter.</p>

<p>For each specific type of single-line receiver selected at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']] there is an appropriate type of receiver channel allocation saved in MICROBEAST PLUS. Please refer to the tables below. Use the column that represents your receiver type and the Status-LED color that was set at [[Manuals:MB_Plus:Receiver_setup_menu_A|menu point '''A''']] and check if your radio transmits the channels in the defined order respectively each stick function on the radio is transmitted using the specified channel number on the left. To know the channel assignment of your transmitter you can check the user manual of the transmitter or look at the servo monitor of the transmitter if it has this feature. If in doubt ask the manufacturer of your transmitter.</p>

<p>

<!--

{|cellspacing="0" cellpadding="2" border="1" style="text-align:center;border:0px solid; padding:0px"

{|cellspacing="0" cellpadding="2" border="1" style="text-align:center;border:0px solid; padding:0px"

!colspan="2" style="color:white; background-color:white; border:0px solid"|

!colspan="2" style="color:white; background-color:white; border:0px solid"|

|-style="font-size: 13px; text-align:center;"

|-style="font-size: 13px; text-align:center;"

| '''9''' || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output

| '''9''' || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output || CH6 Output

|}</p>

|} -->

<p>

<p>

<span style="font-size: 13px;">&#42;Channel designation of Spektrum® transmitters:</span>

:<span style="font-size: small;">&#42;Channel designation of Spektrum® transmitters:</span>

{|cellpadding="2" cellspacing="0" border="1" style="font-size: 12px; text-align:center;"

:{|cellpadding="2" cellspacing="0" border="1" style="font-size: x-small; text-align:center;"

| style="width:80px;" | '''1''' || style="width:80px;" | '''2''' || style="width:80px;" | '''3''' || style="width:80px;" | '''4''' || style="width:80px;" | '''5''' || style="width:80px;" | '''6''' || style="width:80px;" | '''7''' || style="width:80px;" | '''8''' || style="width:80px;" | '''9'''

| style="width:65px;" | '''1''' || style="width:65px;" | '''2''' || style="width:65px;" | '''3''' || style="width:65px;" | '''4''' || style="width:65px;" | '''5''' || style="width:65px;" | '''6''' || style="width:65px;" | '''7''' || style="width:65px;" | '''8''' || style="width:65px;" | '''9'''

|-

|- style="font-size: x-small; text-align:center;"

|THROTTLE || AILERON || ELEVATOR  || RUDDER || GEAR || AUX1 || AUX2 || AUX3 || AUX4

|THROTTLE || AILERON || ELEVATOR  || RUDDER || GEAR || AUX1 || AUX2 || AUX3 || AUX4

|}

|}

</p>

</p>

<span style="font-size: 13px;">&#42;&#42;AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls CH6 Output.<br /></span>

:<span style="font-size: small;">&#42;&#42;AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls CH6 Output.<br /></span>

<span style="font-size: 13px;">&#42;&#42;&#42;Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span>

:<span style="font-size: small;">&#42;&#42;&#42;Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span>

<p>&nbsp;</p>

<p>&nbsp;</p>

<p>

<p>

{{QUOTE|* If the Status-LED stays '''red''' at menu point '''B''', this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

{{QUOTE|* If the Status-LED stays '''red''' at menu point '''B''', this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}</p>

* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}</p>

===Teaching of customized channel order===

===Teaching of customized channel order===

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.</p>

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.</p>

<p>&nbsp;</p>

<p>&nbsp;</p>

{{QUOTE|If the Status-LED stays '''red''' at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.}}

{{QUOTE|* If the Status-LED stays '''red''' at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point '''N''']] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point '''L''']]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}</p>

{{QUOTE|Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point '''N''']] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point '''L''']]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}

<p>

<p>

----

----

----

----

</p>

</p>