Bureaucrats, Administrators, translate-proofr
16,348
edits
Changes
Jump to navigation
Jump to search
Line 53:
Line 53: − + − + Line 61:
Line 61: − + − + + + + + + + + + + +
no edit summary
'''MICROBEAST PLUS / NANOBEAST'''<br />
'''MICROBEAST PLUS / NANOBEAST'''<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. On the MICROBEAST PLUS LED '''H''' will flash alternating with all other LEDs for 2 seconds, then the device will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
<br />
<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[AUX|PIT|RUD]''' port.
* Insert a Spektrum® ''Bind Plug'' at the '''[AUX|PIT|RUD]''' port.
* Disconnect(!) the Spektrum® remote satellite
* Disconnect(!) the Spektrum® remote satellite
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' will flash alternating with all other LEDs for 2 seconds, then MICROBEAST will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
<br />
<br />
<br />
<br />
<gallery mode="nolines">
File:DSMXbind MB ULTRA 1.jpg|You need: RX, bind plug and battery
File:DSMXbind MB ULTRA 2.jpg|Connect bind plug at [AUX|PIT|RUD]
File:DSMXbind MB ULTRA 3.jpg|Power up MICROBEAST: LED A flashes
File:DSMXbind MB ULTRA 4.jpg|Connect your RX, it will also flash
File:DSMXbind MB ULTRA 5.jpg|Start bind sequence on radio
File:DSMXbind MB ULTRA 6.jpg|Binding successful
File:DSMXbind MB ULTRA 7.jpg|RECEIVER MENU point A
</gallery>
=BEASTX setup= <!--T:13-->
=BEASTX setup= <!--T:13-->