Changes

=StudioX app= <!--T:8-->

=StudioX app= <!--T:8-->

When StudioX is started and your BEASTX system is connected to StudioX, choose '''Basic heli setup''' from the device overview page to enter the setup wizard. This will lead you through the basic setup procedure of the SETUP MENU. The options you see here are basically similar to the LED menu of the device, but there might be little differences because of the different nature of the interactive setup. The adjustment is made using the buttons and dials in the app, sometimes interaction with your radio transmitter is necessary. Click '''Next''' at the bottom of each setup step to skip to the following Menu Point. From the dropdown list at the top also you can directly access specific setup items if necessary, but for the first time setup it is recommended to proceed step-by-step beginning at ''Device Orientation'' and ending with ''Cyclic directions''. Adjustment procedure is described at each step briefly. If necessary refer to this manual if you need further assistance. When the setup is finished click the '''Home button''' in the top left corner to get back to the overview screen or disconnect the device and deactivate the BLE2SYS module by clicking the '''Disconnect button''' in the top right corner when adjustment is finished completely.<br />

When StudioX is started and your BEASTX system is connected to StudioX, choose '''Basic heli setup''' from the device overview page to enter the setup wizard. This will lead you through the basic setup procedure of the SETUP MENU. The options you see here are basically similar to the LED menu of the device, but there might be little differences because of the different nature of the interactive setup. The adjustment is made using the buttons and dials in the app, sometimes interaction with your radio transmitter is necessary. Click '''Next''' at the bottom of each setup step to skip to the following Menu Point. From the dropdown list at the top also you can directly access specific setup items if necessary, but for the first time setup it is recommended to proceed step-by-step beginning at ''Device Orientation'' and ending with ''Cyclic limit''. Adjustment procedure is described at each step briefly. If necessary refer to this manual if you need further assistance. When the setup is finished click the '''Home button''' in the top left corner to get back to the overview screen or disconnect the device and deactivate the BLE2SYS module by clicking the '''Disconnect button''' in the top right corner when adjustment is finished completely.<br />

<br />

<br />

<!--T:23-->

<!--T:23-->

You won't be able to access some menu options until the system did finish initialization sequence. So make sure the radio system is powered up and bound correctly and proceed with [[Manuals:MBUltraFblV5:ReceiverType/en|RECEIVER MENU adjustment]] first, if necessary!<br />

You won't be able to access some menu options until the system did finish initialization sequence. So make sure the radio system is powered up and bound correctly and proceed with [[Manuals:BXFbl:ReceiverType/en|RECEIVER MENU adjustment]] first, if necessary!<br />

<br />

<br />

<br />

<br />

<!--T:24-->

<!--T:24-->

{{WARNING_QUOTE|'''Always disconnect your BLE2SYS from the app when you attempt to fly, in order to deactivate the module. Or disconnect it physically from your MICROBEAST ULTRA.''' When the module is active this can cause interference with your radio system as the BLE2SYS is also sending on the 2.4GHz band!<br />

{{WARNING_QUOTE|'''Always disconnect your BLE2SYS from the app when you attempt to fly, in order to deactivate the module. Or disconnect it physically from your BEASTX system.''' When the module is active this can cause interference with your radio system as the BLE2SYS is also sending on the 2.4GHz band!<br />

<br />

<br />

'''Also always make sure the system is in operation mode!''' When it is still in one of the adjustment menus the gyro control and the stick controls may be disabled and you will not be able to fully control your helicopter! By physically disconnecting your USB2SYS/BLE2SYS the system will automatically exit any open menu step and will get into operation mode.}}<br />

'''Also always make sure the system is in operation mode!''' When it is still in one of the adjustment menus the gyro control and the stick controls may be disabled and you will not be able to fully control your helicopter! By physically disconnecting your USB2SYS/BLE2SYS the system will automatically exit any open menu step and will get into operation mode.}}<br />