Changes

<br />

<br />

When using a HOTT or S.Port receiver with separate telemetry wire connected at [SYS], the control wire of your Hobbywing® ESC is connected to port [IO2]. The programming port of your Hobbywing® ESC must be connected to the [SAT] port at the side of your MICROBEAST PLUS/ULTRA (3rd pin from the front!).<br />

When using a HOTT or S.Port receiver with separate telemetry wire connected at [SYS], the control wire of your Hobbywing® ESC is connected to port [IO2]. The programming port of your Hobbywing® ESC must be connected to the [SAT] port at the side of your MICROBEAST PLUS/ULTRA (3rd pin from the front!).<br />

<br />

<br />

If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />

If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />

<br />

<br />

<br />

<br />

{{QUOTE|Please note that this is not an official telemetry connection and the data may be inaccurate or not available at all. This depends heavily on the firmware of the ESC which we can't influence.}}<br />

{{QUOTE|Please note that this is not an official telemetry connection and the data may be inaccurate or not available at all. This depends heavily on the firmware of the ESC which we can't influence.}}<br />

<br />

<br />

To connect your BEASTX system with your JIVE ESC you need a special type of wire. As shown below, the telemetry signal pin on ESC side is the middle pin of the debug connector. The outer pin is common ground. On MICROBEAST PLUS/ULTRA you connect the signal wire to the upper pin of port [IO2] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [IO2]!'''<br />

To connect your BEASTX system with your JIVE ESC you need a special type of wire. As shown below, the telemetry signal pin on ESC side is the middle pin of the debug connector. The outer pin is common ground. On MICROBEAST PLUS/ULTRA you connect the signal wire to the upper pin of port [IO2] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [IO2]!'''<br />

<br />

<br />

Connect the throttle wire (MASTER port) of your KONTRONIK® ESC to port [IO1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST ULTRA.<br />

Connect the throttle wire (MASTER port) of your KONTRONIK® ESC to port [IO1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST ULTRA.<br />

<br />

<br />

When using a HOTT or S.Port receiver with separate telemetry wire connected at [SYS], the throttle wire of your JIVE ESC is connected to port [IO2]. The signal wire for the telemetry must be connected to the [SAT] port at the side of your MICROBEAST PLUS/ULTRA (3rd pin from the front!).<br />

When using a HOTT or S.Port receiver with separate telemetry wire connected at [SYS], the throttle wire of your JIVE ESC is connected to port [IO2]. The signal wire for the telemetry must be connected to the [SAT] port at the side of your MICROBEAST PLUS/ULTRA (3rd pin from the front!).<br />

<br />

<br />

{|style="text-align:center;"

{|style="text-align:center;"

|[[File:Jive.png|x250px|none]]  

|[[File:Jive.png|x250px|none]]  

<br />

<br />

{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the debug port of your JIVE ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />

{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the debug port of your JIVE ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />

<br />

<br />

<br />

<br />

To connect MICROBEAST ULTRA with your JIVE PRO/KOSMIK ESC you need a special type of wire. You can get a ready to use solution from Kontronik® - Ordernr. 9703 (TELEMETRY CABLE JR). As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground on JIVE Pro ESCs. On KOSMIK the pin next to the "LED side" is common ground. It is highly recommended to use a multimeter and check polarity before connecting your ESC to MICROBEAST ULTRA. Note that the pin on the opposite side carries +5V. Do not connect anything here!<br />

To connect MICROBEAST ULTRA with your JIVE PRO/KOSMIK ESC you need a special type of wire. You can get a ready to use solution from Kontronik® - Ordernr. 9703 (TELEMETRY CABLE JR). As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground on JIVE Pro ESCs. On KOSMIK the pin next to the "LED side" is common ground. It is highly recommended to use a multimeter and check polarity before connecting your ESC to MICROBEAST ULTRA. Note that the pin on the opposite side carries +5V. Do not connect anything here!<br />

<br />

<br />

On MICROBEAST ULTRA side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [IO2]!'''<br />

On MICROBEAST ULTRA side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [IO2]!'''<br />

<br />

<br />

Connect the control wire (MASTER port) of your KONTRONIK® ESC to port [IO1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST ULTRA.<br />

Connect the control wire (MASTER port) of your KONTRONIK® ESC to port [IO1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST ULTRA.<br />

<br />

<br />

{|style="text-align:center;"

{|style="text-align:center;"

|[[File:Jive_PRO.png|x250px|none]]  

|[[File:Jive_PRO.png|x250px|none]]  

<br />

<br />

{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />

{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />

<br />

<br />

<br />

<br />

Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST ULTRA will convert the data into your radio's protocol as needed.<br />

Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST ULTRA will convert the data into your radio's protocol as needed.<br />

<br />

<br />

<br />

<br />

{|style="text-align:center;"

{|style="text-align:center;"

|[[File:Scorpion.png|x250px|none]]

|[[File:Scorpion.png|x250px|none]]

<br />

<br />

To enable telemetry you must programm your Scorpion® ESC with the supplied '''Sproto plattform'''. Please set parameter '''1E - communication protocol''' to "UnSc". For further assistance please read the manual for your ESC or contact the manufacturer of your ESC.<br />

To enable telemetry you must programm your Scorpion® ESC with the supplied '''Sproto plattform'''. Please set parameter '''1E - communication protocol''' to "UnSc". For further assistance please read the manual for your ESC or contact the manufacturer of your ESC.<br />

<br />

<br />

{|cellpadding="10" cellspacing="0" border="0" style="text-align:center;"

{|cellpadding="10" cellspacing="0" border="0" style="text-align:center;"

|[[File:sproto_1_.png|x250px|none]]

|[[File:sproto_1_.png|x250px|none]]

<br />

<br />

Spektrum® AVIAN ESC do not have a separate line for telemetry data. Here motor control and telemetry data is sent bidirectional on the main connection wire. For this we must connect the AVIAN ESC to the [SYS] port of MICROBEAST PLUS/ULTRA, as the other connectors [IO1] and [IO2] can only work in one direction. Thus it is not possible to use a HOTT or S.Port receiver with separate telemetry wire, as this needs to be connected at [SYS] port as well.<br />

Spektrum® AVIAN ESC do not have a separate line for telemetry data. Here motor control and telemetry data is sent bidirectional on the main connection wire. For this we must connect the AVIAN ESC to the [SYS] port of MICROBEAST PLUS/ULTRA, as the other connectors [IO1] and [IO2] can only work in one direction. Thus it is not possible to use a HOTT or S.Port receiver with separate telemetry wire, as this needs to be connected at [SYS] port as well.<br />

<br />

<br />

Please note that you must activate the [SYS] port connection for Spektrum® SMART operation at RECEIVER MENU point '''L'''.<br />

Please note that you must activate the [SYS] port connection for Spektrum® SMART operation at RECEIVER MENU point '''L'''.<br />

<br />

<br />

<br />

<br />

</translate>

</translate>