Changes

[[File:TXGovSetup 10.jpg|200px]]

[[File:TXGovSetup 10.jpg|200px]]

[[File:TXGovSetup 11.jpg|200px]]<br />

[[File:TXGovSetup 11.jpg|200px]]<br />

<br/>

<br />

(5) Wechseln Sie durch kurzen Tastendruck zu Einstellpunkt C und bringen Sie den Gassteuerknüppel in Vollgasposition. Wieder wird die Status LED blau leuchten und somit signalisieren, dass die Vollgasposition erkannt wurde. Drücken Sie zur Bestätigung erneut kurz auf den Taster.<br />

(5) Wechseln Sie durch kurzen Tastendruck zu Einstellpunkt C und bringen Sie den Gassteuerknüppel in Vollgasposition. Wieder wird die Status LED blau leuchten und somit signalisieren, dass die Vollgasposition erkannt wurde. Drücken Sie zur Bestätigung erneut kurz auf den Taster.<br />

[[File:TXGovSetup 12.jpg|200px]]<br />

[[File:TXGovSetup 12.jpg|200px]]<br />

[[File:TXGovSetup 14.jpg|200px]]

[[File:TXGovSetup 14.jpg|200px]]

[[File:TXGovSetup 15.jpg|200px]]

[[File:TXGovSetup 15.jpg|200px]]

[[File:TXGovSetup 16.jpg|200px]]<br/>

[[File:TXGovSetup 16.jpg|200px]]<br />

<br/>

<br />

In normal flight mode set the curve flat to 0, so the motor can't start when powering up.<br />

In normal flight mode set the curve flat to 0, so the motor can't start when powering up.<br />

[[File:TXGovSetup 17.jpg|200px]]<br/>

[[File:TXGovSetup 17.jpg|200px]]<br />

<br/>

<br />

Set flat throttle curves for the other flight modes as high as necessary to gain a specific rotor head speed according to the throttle tables shown in the MICROBEAST ProEdition Addon manual. In this example we use 1800rpm = 45%, 2080rpm = 52% and 2000 rpm = 50%. The Status LED should light up in "red" colour when switching to those flight modes.<br />

Set flat throttle curves for the other flight modes as high as necessary to gain a specific rotor head speed according to the throttle tables shown in the MICROBEAST ProEdition Addon manual. In this example we use 1800rpm = 45%, 2080rpm = 52% and 2000 rpm = 50%. The Status LED should light up in "red" colour when switching to those flight modes.<br />

[[File:TXGovSetup 18.jpg|200px]]

[[File:TXGovSetup 18.jpg|200px]]

[[File:TXGovSetup 19.jpg|200px]]

[[File:TXGovSetup 19.jpg|200px]]

[[File:TXGovSetup 20.jpg|200px]]<br/>

[[File:TXGovSetup 20.jpg|200px]]<br />

<br/>

<br />

For Autorotation bail out set the throttle curve to a flat 10%. The Status LED should light up in "blue" when Autorotation switch is enabled.<br />

For Autorotation bail out set the throttle curve to a flat 10%. The Status LED should light up in "blue" when Autorotation switch is enabled.<br />

[[File:TXGovSetup 21.jpg|200px]]<br />

[[File:TXGovSetup 21.jpg|200px]]<br />

<br/>

<br />

That's it. '''Switch back to your normal mode (motor off!)''' and proceed with the following steps E, F, G, H as described in the MICROBEAST PLUS ProEdition manual. After exiting the menus you can do a little bench test. When switching to idle up the motor should start to run slowly, then after a short time of stabilization the rpm will increase more forceful (it is not unusual that without rotor blades or with main gear removed the motor may run erratic or the rpm may pump a little bit during spoolup because of the unloaded condition!). If it takes very long time (a few seconds) until the motor starts to initially run, you may readjust the throttle low point at Governor menu point B. Typically the distance between motor off and motor start position is too large then.

That's it. '''Switch back to your normal mode (motor off!)''' and proceed with the following steps E, F, G, H as described in the MICROBEAST PLUS ProEdition manual. After exiting the menus you can do a little bench test. When switching to idle up the motor should start to run slowly, then after a short time of stabilization the rpm will increase more forceful (it is not unusual that without rotor blades or with main gear removed the motor may run erratic or the rpm may pump a little bit during spoolup because of the unloaded condition!). If it takes very long time (a few seconds) until the motor starts to initially run, you may readjust the throttle low point at Governor menu point B. Typically the distance between motor off and motor start position is too large then.