Bureaucrats, Administrators, translate-proofr
15,724
edits
Changes
Jump to navigation
Jump to search
Line 116:
Line 116: + + + + + + + + + + + + + + + + + + + + + + + + + + + − + Line 136:
Line 163: − + − − ===How can I increase rotation rate for aileron, elevator and rudder?=== <!--T:31--> − − <!--T:32--> − The rotation speed of the helicopter is only determined by the length of the stick output signal. The gyros measure the actual rotation rate and the system will move the helicopter as fast as it is determined by the stick position. So simply increasing/decreasing the stick throw (mostly done by increasing/decreasing servo throw or using Dualrate in the TX for the specified function) will increase/decrease rotaion rate. Note that the rotation rate in first line has nothing to do with your cyclic pitch adjustments at Setup menu points J or L and also has nothing to do with the cyclic pitch when steering cyclic on the ground! In flight the system will automaticaly control the pitch as it is necessary to maintain the given rate. So always setup the cyclic pitch as mentioned in the manual and do not rely on what you see when moving the sticks on the ground. − − <!--T:33--> − The presets at Parameter menu point B are nothing else than different preset dualrate/expo curves inside Microbeast. Choose the preset that fits your preferences best and that gives you a good amount of rotation rate. Using the presets (except for the "Transmitter" preset) it is recommended to not change the output signal in the TX significantly as especially when using expo this will bend, compress or stretch the curves, leading to very strange flight behavior. It just is not like adding 5% of expo as the curves between TX and Microbeast will multiply and not sum together! Anyhow you may do small adjustments in stick throw, i.e. for slightly increasing the roll rate. This will not significantly deform the Microbeast's internal curves. − But easiest thing to do would be to switch flight behaviour to preset blue (="Transmitter") and adjust the curves in your transmitter just as you like. Therefor we suggest to start with a setting of 70% D/R and 25% expo on cylic and 85% D/R and 40% expo on tail in the transmitter and adjust the curves accordingly. When setting parameter B to "blue = TX" the internal curves in Microbeast will be "disabled". Here 100% stick input will give a rotation rate of apprx. 600deg/s on the rudder axis and apprx. 400deg/s for the cyclic movements (this may vary depending on TX brand as any manufacturer use another signal output as maximum, so this also can be 107, 110% or 95%). − We are often asked which percentages of expo or dual rate corresponds to the different presets. As manufacturers calculate expo curves different, we can't tell you what our preset curves correspond to which TXs expo values as we use our own expo calculation and there is no data available for comparing. We did outfly these values and programmed them in the source code so we can't tell what these are in Futaba or JR percentages. If you want to use a specific preset as your starting point we suggest to connect your MICROBEAST to the StudioX software. Here you can see the different values for each control behavior preset and you can create a custom preset for which you may use the given values and adjust them until they perfectly fit your flying style. − − <!--T:34--> − '''Note for MICROBEAST/AR7200BX/Ar7300BX:''' − If Parameter menu point B is set to preset "blue" and the tail gain is switched to heading lock mode you can see in operation mode by the Status LED state at which tail − stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position the Status LED will start to flash. Moving the stick − to this point in flight the rotation rate of the helicopter will be as high as the gyro can control. Increasing the stick throw further the LED will go off. At this − point the rate control is switched off and the tail will spin freely. Here the only limit is the tail pitch throw and normaly the tail will spin ultra − fast. This can be used for performing tail slides or turns with very fast spinning tail. For normal flying around you should not use this as you may − accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven. So please check on the ground that the Status LED will not go off when giving − full rudder stick deflection in your default flight modes. − − <!--T:53-->
no edit summary
* Check for correct wiring or setup of tail gain cable/channel.
* Check for correct wiring or setup of tail gain cable/channel.
Additionaly when the elevator doesn't seem to work either, maybe the wrong mounting orientation has been selected. So select the correct mounting orientation in Setup menu point '''A'''.
Additionaly when the elevator doesn't seem to work either, maybe the wrong mounting orientation has been selected. So select the correct mounting orientation in Setup menu point '''A'''.
===How can I increase rotation rate for aileron, elevator and rudder?=== <!--T:31-->
<!--T:32-->
The rotation speed of the helicopter is only determined by the length of the stick output signal. The gyros measure the actual rotation rate and the system will move the helicopter as fast as it is determined by the stick position. So simply increasing/decreasing the stick throw (mostly done by increasing/decreasing servo throw or using Dualrate in the TX for the specified function) will increase/decrease rotaion rate. Note that the rotation rate in first line has nothing to do with your cyclic pitch adjustments at Setup menu points J or L and also has nothing to do with the cyclic pitch when steering cyclic on the ground! In flight the system will automaticaly control the pitch as it is necessary to maintain the given rate. So always setup the cyclic pitch as mentioned in the manual and do not rely on what you see when moving the sticks on the ground.
<!--T:33-->
The presets at Parameter menu point B are nothing else than different preset dualrate/expo curves inside Microbeast. Choose the preset that fits your preferences best and that gives you a good amount of rotation rate. Using the presets (except for the "Transmitter" preset) it is recommended to not change the output signal in the TX significantly as especially when using expo this will bend, compress or stretch the curves, leading to very strange flight behavior. It just is not like adding 5% of expo as the curves between TX and Microbeast will multiply and not sum together! Anyhow you may do small adjustments in stick throw, i.e. for slightly increasing the roll rate. This will not significantly deform the Microbeast's internal curves.
But easiest thing to do would be to switch flight behaviour to preset blue (="Transmitter") and adjust the curves in your transmitter just as you like. Therefor we suggest to start with a setting of 70% D/R and 25% expo on cylic and 85% D/R and 40% expo on tail in the transmitter and adjust the curves accordingly. When setting parameter B to "blue = TX" the internal curves in Microbeast will be "disabled". Here 100% stick input will give a rotation rate of apprx. 600deg/s on the rudder axis and apprx. 400deg/s for the cyclic movements (this may vary depending on TX brand as any manufacturer use another signal output as maximum, so this also can be 107, 110% or 95%).
We are often asked which percentages of expo or dual rate corresponds to the different presets. As manufacturers calculate expo curves different, we can't tell you what our preset curves correspond to which TXs expo values as we use our own expo calculation and there is no data available for comparing. We did outfly these values and programmed them in the source code so we can't tell what these are in Futaba or JR percentages. If you want to use a specific preset as your starting point we suggest to connect your MICROBEAST to the StudioX software. Here you can see the different values for each control behavior preset and you can create a custom preset for which you may use the given values and adjust them until they perfectly fit your flying style.
<!--T:34-->
{{QUOTE|'''Note for MICROBEAST/AR7200BX/Ar7300BX (not MICROBEAST PLUS):''' If Parameter menu point '''B''' is set to preset "blue" and the tail gain is switched to heading lock mode you can see in operation mode by the Status LED state at which tail stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position the Status LED will start to flash. Moving the stick to this point in flight the rotation rate of the helicopter will be as high as the gyro can control. Increasing the stick throw further the LED will go off. At this point the rate control is switched off and the rudder axis will spin uncontrolled. Here the only limit is the tail pitch throw and normaly the tail will spin ultra fast. This can be used for performing tail slides or turns with very fast spinning tail. For normal flying around you should not use this as you may accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven. So please check on the ground that the Status LED will not go off when giving full rudder stick deflection in your default flight modes.}}<br />
<!--T:53-->
===The helicopter wobbles on aileron and elevator axis.===
''Reducing the swashplate gain does not help to suppress this effect completely.''<br />
* The helicopter‘s linkage ratio is not suitable for flybarless usage. In Setup menu point J adjust the cyclic pitch to exactly 6 degrees and make sure the color of the Status-LED lights up “blue”. If this is not the case change the mechanical linkage ratio of the helicopter (i.e. by moving the linkage balls further inwards on the servo horns, by mounting longer linkage balls on the swash plate outer ring or by mounting shorter linkage balls on the swash plate inner ring).
* The servo-blade combination is not good. Use faster and stronger servos and/or specific flybarless blades.
* Some linkages aren’t moving smoothly and freely. Check the mechanics for any hard points (ball linkages, blade grips). Check if the dampers are greased and that the thrust bearings in the blade grips are correctly mounted.
* Imbalance of the main rotor head. Firstly, do not tighten rotor blade bolts to much. The blades must be able to align themselves by centrifugal force. Then check blade balancing and/or try a different set of rotor blades.
===The tail rotor turns around instantly when doing backwards flying.===
* Tail gyro gain too low. Increase tail gyro gain as described [[Manuals:MB_Plus:Flying|here]] and make sure you're using the tail gyro in HeadingLock mode (using Normal-Rate mode it is nearly impossible to perform backwards maneuvers!).
* No sufficient thrust produced by the tail rotor. Check tail pitch angles. Reduce the maximum amount of available tail pitch throw at [[Manuals:MB_Plus:Setupmenu_E|Setup menu point '''E''']] to prevent the tail blades from stalling or increase the tail pitch angle if it‘s too small. Use different (larger) tail rotor blades or increase the rotor rpm.
===Helicopter tips over when trying to take off or tilts to one side in flight.=== <!--T:23-->
===Helicopter tips over when trying to take off or tilts to one side in flight.=== <!--T:23-->
* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!
* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly ([[Manuals:MB_Plus:Setupmenu_M|Setup menu point '''M''']])!
<!--T:24-->
<!--T:24-->
<!--T:30-->
<!--T:30-->
{{QUOTE|'''Please do not confuse:''' A slight tilt of the swash plate when the heli is standing on the ground is absolutely normal when the so-called integrators are not fully discharged. Especially when carrying the heli or steering the sticks this can happen as the system tries to perform the necessary commands. But as the helicopter will not move as intended the system tries to keep the servo movement until the helicopter may turn. Only after approx. 30 seconds without moving the helicopter or touching the sticks, the swash will return to its normal position as the systems slowly clears its memory. The exact amount of time for this depends on the position of the thrust stick. In the middle position is the discharge at the fastest. So if possible always keep the thrust stick in center position when the heli is on the ground so that the swash plate stays leveled. Once the helicopter is airborne you will not see any of these effects as now the control loop can operate as intended. As described [[Manuals:MB_Plus:Flying|here]] to center the swashplate you can also move the cyclic stick(s) to full deflection once as this will clear integrator instantly. Only if the swash moves downright by itself to full-stop even after correcting with the sticks and only cycling power off and on resolves this problem, check that your transmitter does not send any unwanted control commands (trimming active, stick pots worn out, ...). If this is not the case please contact support as maybe there is some problem with the sensors then.}}
{{QUOTE|'''Please do not confuse:''' A slight tilt of the swash plate when the heli is standing on the ground is absolutely normal when the so-called integrators are not fully discharged. Especially when carrying the heli or steering the sticks this can happen as the system tries to perform the necessary commands. But as the helicopter will not move as intended the system tries to keep the servo movement until the helicopter may turn. Only after approx. 30 seconds without moving the helicopter or touching the sticks, the swash will return to its normal position as the systems slowly clears its memory. The exact amount of time for this depends on the position of the thrust stick. In the middle position is the discharge at the fastest. So if possible always keep the thrust stick in center position when the heli is on the ground so that the swash plate stays leveled. Once the helicopter is airborne you will not see any of these effects as now the control loop can operate as intended. As described [[Manuals:MB_Plus:Flying|here]] to center the swashplate you can also move the cyclic stick(s) to full deflection once as this will clear integrator instantly. Only if the swash moves downright by itself to full-stop even after correcting with the sticks and only cycling power off and on resolves this problem, check that your transmitter does not send any unwanted control commands (trimming active, stick pots worn out, ...). If this is not the case please contact support as maybe there is some problem with the sensors then.}}<br />
<br />
<br />