Changes

<br />

<br />

=General=

=General=

Due to a plugin-based architecture StudioX is compatible with many different devices. At the moment there are plugins available for the following devices:

Due to a plugin-based architecture StudioX is compatible with many different devices:

* [[StudioX_Microbeast_Plugin/en|MICROBEAST]]

* [[StudioX_Microbeast_Plugin/en|MICROBEAST]]

* [[Studiox_microbeast_plus_plugin/en|MICROBEAST PLUS / MICROBEAST PLUS HD]]

* [[Studiox_microbeast_plus_plugin/en|MICROBEAST PLUS / MICROBEAST PLUS HD]]

* [[Studiox_ar7200bx_plugin/en|SPEKTRUM AR7200BX / SPEKTRUM AR7300BX]]

* [[Studiox_ar7200bx_plugin/en|SPEKTRUM AR7200BX / SPEKTRUM AR7300BX]]

* [[Studiox_ar7210bx_plugin/en|SPEKTRUM AR7210BX]]

* [[Studiox_ar7210bx_plugin/en|SPEKTRUM AR7210BX]]

* RCWare RX2SIM Multi-SIM Adapter

* [[Studiox_BLE2SYS_plugin/en|BLE2SYS bluetooth LE adapter]]

* [[Studiox_RX2SIM_plugin/en|RCWare RX2SIM Wireless Multi-SIM Adapter]]

<br />

<br />

The plugins provide the following functionality*:

The plugins may provide the following functionality:

* administration

* administration

* configuration

* configuration

* updating

* updating and buying software upgrades

* backup and restore

* backup and restore your settings

''*The range of functions can vary.''<br />

* load predefined presets<br />

<br />

<br />

== Connecting a BEASTX device ==

All BEASTX devices come with a serial communication port which typically is marked with the letters ''SYS''. Connect the servo wire coming from your USB interface to this port. Make sure to connect the wire in correct polarity on both sides! When using a USB2SYS / SPEKTRUM SPMA3030 interface you have to power the device with a separate power supply, i.e. receiver battery or BEC of the helicopter. It will not be powered from the USB interface.<br />

== Connecting a BEASTX gyro to the computer ==

All BEASTX gyros come with a serial communication port which typically is marked with the letters ''SYS''. Connect the servo wire coming from your USB interface to this port. Make sure to connect the wire in correct polarity on both sides! When using the USB2SYS interface you have to power the device with a separate power supply, i.e. receiver battery or BEC of the R/C model. It will not be powered from the USB port.<br />

<br />

<br />

  <div style= "padding: 0px 50px;">

  <div style= "padding: 0px 50px;">

<br />

<br />

<br />

<br />

When using the RX2SIM in USB2SYS emulation mode to connect your BEASTX device to the computer the device will be powered from the USB port. Anyhow, this only will work when receiver and servos are not connected to your MICROBEAST / AR7xxxBX ! Otherwise the power of the USB port will not be sufficient to supply all consumers. In this case you have to power the device from the receiver battery as well. '''But here when using more than 6 Volts (i. e. using a 2s Lipo battery as receiver power supply) you must disconnect the red wire (plus pole) from the servo wire going to the interface. Otherwise you will damage the RX2SIM and/or USB port of your computer!'''<br />

Also you can use a RX2SIM Wireless Multi-Sim Adapter instead of the USB2SYS interface. For this you can switch the RX2SIM into an USB2SYS emulation mode (push button on the RX2SIM several times until the LED lights up in orange color). In this configuration the BEASTX gyro will be powered from the USB port. Anyhow, this only will work when receiver and servos are not connected to the gyro! Otherwise the power of the USB port will not be sufficient to supply all consumers. In this case you have to power the device from the receiver battery as well. '''But here when using more than 6 Volts (i. e. using a 2s Lipo battery as receiver power supply) you must disconnect the red wire (plus pole) from the servo wire going to the interface. Otherwise you will damage the RX2SIM and/or USB port of your computer!'''<br />

<br />

<br />

<table>

<table>