Line 29: |
Line 29: |
| Wenn Änderungen noch nicht abgespeichert wurden: | | Wenn Änderungen noch nicht abgespeichert wurden: |
| * werden die bestehenden Werte in der Ansicht hellblau hinterlegt | | * werden die bestehenden Werte in der Ansicht hellblau hinterlegt |
− | * leuchtet im unteren Bereich des Fensters die Meldung "Unsaved Settings" und die Anzahl der geänderten aber nicht gespeicherten Werte auf | + | * leuchtet im unteren Bereich des Fensters die Meldung "Unsaved Settings" und die Anzahl der geänderten aber nicht gespeicherten Werte auf<br /> |
| + | <br /> |
| | | |
| =Setupmenü Übersicht= | | =Setupmenü Übersicht= |
Line 116: |
Line 117: |
| <br /> | | <br /> |
| | | |
− | =Update Firmware= | + | =Firmwareupdate (Update Firmware)= |
− | If you did get a firmware file from the BEASTX support you can open and upload this firmware file to your device here. Usually you don't need to get here when you want to perform a firmware update as update files offered on the "Device Overview" tab can directly be uploaded to your device by clicking on them.<br />
| + | Wenn Sie vom BEASTX Support eine spezielle Firmware Datei bekommen haben können Sie diese hier öffnen und auf den AR7200BX /AR7300BX laden. Ansonsten wird dieser Menüpunkt nicht benötigt. Regulär können Firmware Dateien direkt durch Auswahl in der Hauptübersicht ("Device Overview") angefordert und automatisch hochgeladen werden.<br /> |
| <br /> | | <br /> |
| | | |
− | =Advanced plug-in configuration= | + | =Plug-In Konfiguration= |
− | From the StudioX main menu, open "Edit" then "Configure plug-ins..." to show the plug-in Configuration dialog.<br />
| + | Wählen Sie in der Menüleiste "Edit" und klicken Sie auf "Configure plug-ins..." um die Konfigurationsansicht für die StudioX Plug-Ins aufzurufen. Wählen sie in der Liste das "AR7x00BX" Plug-In:<br /> |
− | Select "AR7x00BX" from the list:<br />
| + | <br /> |
| [[File:Mb_config_dlg.png|200px|thumb|none]] | | [[File:Mb_config_dlg.png|200px|thumb|none]] |
− | <br />
| + | ==Interface Einstellungen (Serial Port Control)== |
− | ==Serial Port Control== | + | Standardmäßig versucht das AR7200BX / AR7300BX Plug-In über sämtliche vorhandenen seriellen Schnittstellen einen SPEKTRUM AR7200BX / AR7300BX zu erreichen (das USB2SYS/SPMA3030-Interface bildet eine serielle Schnittstelle). Manchmal kann es notwendig sein bestimmte Schnittstellen von der Suche auszuschließen, z. B. wenn eine Schnittstelle das Plug-In blockiert. Hierfür gibt es zwei Möglichkeiten |
− | By default the AR7200BX/AR7300BX plug-in will continuously try to query all serial interfaces (the USB2SYS/SPMA3030-Interface is a serial interface) to check if an AR7200BX/AR7300BX is connected somewhere.<br />
| + | * Ausschluss der angewählten Ports ("Use all ports, except those selected") |
− | Sometimes it is useful to limit the ports that the plug-in is trying to query, i.e. in case a port is blocking the plug-in. Therefore you can choose from one of the following options:
| + | * Suche nur auf den angewählten Ports ("Only use selected ports") |
− | * Use all ports, except those selected | + | Wählen Sie aus ob das Ein- oder Ausschlusskritierium angewendet werden soll und markieren sie den Port der verwendet bzw. der ausdrücklich nicht verwendet werden soll.<br /> |
− | * Only use selected ports | + | ==Gerätesuchintervall (Device Discovery)== |
− | Use the entries in the list below to refine your selection. The plug-in will only try to query ports which match the selected rule.<br />
| + | Dieser Wert bestimmt in welchen Zeitabständen die Gerätesuche wiederholt wird. Normalerweise sollte der voreingestellte Wert gut funktionieren.<br /> |
− | ==Device Discovery== | |
− | This specifies the interval time which is used to try identifying newly connected devices. This should not be modified if the mechanism is working properly.<br />
| |
| <br /> | | <br /> |