Translations:Help:FAQ:General/9/en

From BEASTX Wiki
Revision as of 13:28, 9 November 2017 by FuzzyBot (talk | contribs) (Importing a new version from external source)
Jump to navigation Jump to search

MICROBEAST PLUS


  When updating from firmware 4.x.x or lower to Version 5.x.x you will loose all your settings. Please carefully read the Version 5 instruction manual and do the basic setup again.



5.0.2

Basic functionality
  • now fully adjustable (Setup & Parameters) also with StudioX computer software or StudioXm mobile App; see manuals for further information
  • added support for FlySky iBus and Jeti EXBUS serial line input data
  • Spektrum/JR remote satellite can be directly connected to pin board of MICROBEAST PLUS (Spektrum Adapter not required anymore); see manual for further information
  • added separate trim values for aileron, elevator, collective and rudder
  • removed "User defined" presets instead you can directly edit a value with StudioX/StudioXm if necessary
  • reworked adjustment in Receiver Menu:
    • Receiver Menu Point A: automatic receiver type detection; see manual for further information
    • Receiver Menu Point A: changed LED colors for receiver types and also changed receiver type naming; see manual for further information
  • reworked adjustment in Setup Menu:
    • in general values and presets are changed using the rudder stick; menu options (selecting servos, changing adjustment positions) are set with aileron; when directions are setup correctly, left stick decreases a value and right stick increases a value
    • Setup Menu Point C (Rudder pulse width): swapped LED colors for 760µs and 960µs (now 760 = purple and 960 = red) so that the values are increasing in the given order from purple (lowest) to blue (highest)
    • Setup Menu Point F (Gyro/Rudder direction): no need to check gyro direction by user anymore, instead teach the rudder direction to the system; see manual for further information
    • swapped Setup Menu Points G and H (now H = Swash servo directions and G = Swash mixing)
    • now supports up to 4 swashplate servos (when choosing 90° eCCPM swash mixing at Setup Point G and using a single wire receiver); 4th servo (2nd elevator) is connected to CH7 output
    • Setup Menu Point J (Cyclic throw): measurement and neutral positions can be selected as often as you like now, so you can even check positions after the setup was finished; see manual for further information
    • Setup Menu Point K (Collective pitch): no need to teach the stick end positions anymore, instead the user has to adjust the pitch range initially so the stick movement and range is shown correctly on the display; see manual for further information
    • Setup Menu Point M (Cyclic directions): no need to check swash gyro compensation by user anymore, instead teach the stick directions to the system; see manual for further information
  • reworked settings in Parameter Menu:
    • Parameter Menu Point A (Quick trim): added collective trim and rudder trim can be done with rudder stick now; see manual for further information
    • Parameter Menu Point L (AttitudeControl Mode): swapped LED colors for different modes (now purple = Angular mode, red = Bailout rescue, blue = 3D - Mode)
  • throttle failsafe indicator (only when using Single line receiver): when throttle is higher than failsafe position and failsafe engages during power up, the system will lock throttle after initialization and the Status LED will flash red/blue!
  • reworked adjustment in Governor Menu:
    • Governor Menu Point D: swapped LED colors for displaying Autorotation and Governor at maximum speed (now purple = Autorotation, blue = Governor at maximum speed)


Internal RPM Governor
  • increased range for electric governor to be used with SAB Goblin Fireball: Maximum headspeed now 5000rpm


PROEDITION
  • added new feature "Bank switching" (can be enabled with StudioX/StudioXm only) which allows to set parameters for three flight conditions; when used gain adjustment using the dials and gyro gain adjustment with the radio are disabled, instead the gains and parameters are all set with StudioX/StudioXm; see manual for further information


StudioX
  • added FFT tab to show frequency spektrum of the sensor input to visualize vibrations, especially interesting when planning to use the AttitudeControl; see StudioX manual for further information