A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each output to one control function of MICROBEAST PLUS by using one connection wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. Connect each wire to the corresponding servo output at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!<br />
+
A receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each servo output to one control function of MICROBEAST PLUS by using one wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to test what each output is used for!<br />
Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any radio system on the market, not only these two brands!
+
Here we show connection layouts for two common radio brands. Note that this is only exemplary, you can use any radio system on the market, not only these two brands! Anyhow, make sure that you connect the wires to the correct functions as mentioned above.
{|cellspacing = "20"
{|cellspacing = "20"
|[[Image:Spektrum_RX.png|x100px]]
|[[Image:Spektrum_RX.png|x100px]]
Line 11:
Line 11:
|}<br />
|}<br />
{{QUOTE|
{{QUOTE|
−
* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!
+
* The wires for rudder, pitch and gyro are all signal wires. Although some have different color, they must be placed on the same receiver side as the the orange wires from aileron and elevator!
* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
−
* The throttle servo/speed controller is connected to the receiver's throttle output. Using the headspeed governor function of MICROBEAST PLUS is not possible in combination with a Standard receiver!}}<br />
+
* The throttle servo/speed controller is connected to the receiver's throttle output. So using the headspeed '''governor function''' of MICROBEAST PLUS is '''not possible''' in combination with a Standard receiver!}}<br />
<br />
<br />
<br />
<br />
Latest revision as of 10:37, 23 February 2023
Standard receiver
A receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each servo output to one control function of MICROBEAST PLUS by using one wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to test what each output is used for!
Here we show connection layouts for two common radio brands. Note that this is only exemplary, you can use any radio system on the market, not only these two brands! Anyhow, make sure that you connect the wires to the correct functions as mentioned above.
The wires for rudder, pitch and gyro are all signal wires. Although some have different color, they must be placed on the same receiver side as the the orange wires from aileron and elevator!
You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
The throttle servo/speed controller is connected to the receiver's throttle output. So using the headspeed governor function of MICROBEAST PLUS is not possible in combination with a Standard receiver!
