Difference between revisions of "Translations:Manuals:MBPlusFblV52:Radio System/7/en"

From BEASTX Wiki
Jump to navigation Jump to search
(Importing a new version from external source)
(Importing a new version from external source)
Line 5: Line 5:
 
BXA76401 but this requires to modify the wiring layout as shown below!<br />
 
BXA76401 but this requires to modify the wiring layout as shown below!<br />
 
<br />
 
<br />
−
In order to connect a SRXL2 remote satellite like SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
+
In order to connect a SRXL2 remote satellite like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
 
<br />
 
<br />
 
{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
 
{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
−
<br />
+
{|cellspacing="50" style="text-align:center;"
−
{|cellspacing="20" style="text-align:center;"
+
|[[Image:SRXL2 AR6610T en.png| x150px]]
−
|[[Image:Mbplus_spektrum_rx2.png | x100px]]
+
|[[Image:SRXL2 Satellite en.png| x180px]]
 
|- style="text-align:center; font-size:75%;"
 
|- style="text-align:center; font-size:75%;"
−
| THIS PICTURE IS WRONG!!!!
+
| AR6610T receiver with standard servo connector
 +
| SRXL2 satellite receiver with modified connector
 
|}<br />
 
|}<br />
−
<br />
 
 
When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
 
When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
 
<br />
 
<br />

Revision as of 14:43, 28 September 2020

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:MBPlusFblV52:Radio System)
== Single wire with telemetry ==
Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL|CH5]''' port.
* When using a telemetry receiver and an '''ESC with telemetry''' data connector, the ESC is connected to '''[ELE|DI1]'''. The data signal of the ESC is connected to '''[AIL|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD|PIT|AUX]; please do not connect anything here!).<br />
<br />
[[File:Warning.png|18px|sub]] '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
<br />
{|cellspacing="50" style="text-align:center;"
|[[Image:SRXL2 AR6610T en.png| x150px]]
|- style="text-align:center; font-size:75%;"
| SRXL2 receiver with standard servo connector and adapter
|}
<br />
<br />
To connect a '''SRXL2 remote receiver''' like '''SPM4650/SPM4651T''' it is necessary to '''INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
{|cellspacing="50" style="text-align:center;"
|[[Image:SRXL2 Satellite en.png| x180px]]
|[[Image:SRXL2 rx kabel.png| 200px]]
|- style="text-align:center; font-size:75%;"
| SRXL2 satellite receiver with modified satellite connector
| Modified 4-pin SRXL connector
|}
{{WARNING_QUOTE|'''Never connect the 4-pin receiver connector to MICROBEAST ULTRA without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
<br />
<br />
Translation=Spektrum® SRXL2 receiver=
Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as remote satellites with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS. '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />
<br />
In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter
BXA76401 but this requires to modify the wiring layout as shown below!<br />
<br />
In order to connect a SRXL2 remote satellite like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
<br />
{{WARNING_QUOTE|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
{|cellspacing="50" style="text-align:center;"
|[[Image:SRXL2 AR6610T en.png| x150px]]
|[[Image:SRXL2 Satellite en.png| x180px]]
|- style="text-align:center; font-size:75%;"
| AR6610T receiver with standard servo connector
| SRXL2 satellite receiver with modified connector
|}<br />
When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
<br />

Spektrum® SRXL2 receiver

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as remote satellites with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS. Please note: MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!

In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!

In order to connect a SRXL2 remote satellite like SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector. In this configuration you can directly plug in the receiver without the need for an extra adapter.

Warning.png Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately! Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.


SRXL2 AR6610T en.png SRXL2 Satellite en.png
AR6610T receiver with standard servo connector SRXL2 satellite receiver with modified connector


When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!

Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Manuals:MBPlusFblV52:Radio_System/7/en&oldid=17704"