JETI EXBUS

EXBUS ist ein sehr vielseitiges Protokoll. Es kann nicht nur Steuerdaten an das Flybarless-System senden, sondern auch Telemetriedaten übertragen und sogar Menüs über die Fernsteuerung oder JETI-Box anzeigen. Du kannst die EXBUS-Datenleitung an verschiedenen Ports deines MICROBEAST oder NANOBEAST anschließen. Stelle sicher, dass die Ausgabe des Empfängers auf EXBUS eingestellt ist (nicht auf UDI, SPPM oder andere).

Anschlussschema

EXBUS Anschlussoptionen

Port	Telemetrie	JETIBox Menü
DI1	nein	nein
SYS	ja	ja
DI2	ja	ja

Die Verwendung von EXBUS zur Steuerung deines Hubschraubers ist mit allen BEASTX-Geräten möglich. Verbinde den EXBUS-Port des Empfängers mit dem DI1 / IO1-Port deines BEASTX-Systems unter Verwendung eines der mitgelieferten Standard-Servokabel.

(Picture MBPLUS)

(Picture Nanobeast)

Der Motorsteller bzw. das Gas-Servo ist am Ausgang CH5 / IO2 angeschlossen.

(Picture MBPLUS)

(Picture Nanobeast)

Für bidirektionale Telemetrie verbinde das EXBUS-Signal entweder mit dem SYS-Port oder dem DI2-Port deines MICROBEAST PLUS / ULTRA. Wenn du den DI2-Port verwendest, wird ein Adapter von Standard-Servoanschluss auf 5-poligen JST-Stecker benötigt, wie unten gezeigt.

(Picture SYS)

(Picture DI2)

MICROBEAST PLUS
Der Motorsteller bzw. das Gasservo wird am DI1-Port angeschlossen. Falls erforderlich, wird die Telemetrie-Datenleitung vom Motorsteller am CH5-Port angeschlossen.

MICROBEAST ULTRA
Der Motorsteller bzw. das Gasservo wird am IO1-Port angeschlossen. Falls erforderlich, wird die Telemetrie-Datenleitung vom Motorsteller am IO2-Port angeschlossen.

NANOBEAST
The ESC or throttle servo is connected at CH1 port. If needed the telemetry data line from the ESC is connected to the SAT port.

Radio setup

Enable EXBUS Telemetry....

BEASTX setup

In order to use your EXBUS receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering for your radio system. By default the BEASTX system has a preset channel order that fits to most JETI radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.

JETI default channel order

Channel	Function
CH1	Throttle
CH2	Roll / Aileron
CH3	Pitch / Elevator
CH4	Thrust / Collective
CH5	Rudder
CH6	Gain
CH7	AttitudeControl (optional)
CH8	Governor (optional)
CH9	Aux channel (optional)

(The optional functions are described in the section Optional features.)

MICROBEAST PLUS / MICROBEAST ULTRA

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section.

NANOBEAST

When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.

When using telemetry and connecting the EXBUS receiver to SYS port we can setup the receiver type in a different way:
Connect a JETI bind plug to the SYS port firstly and power up NANOBEAST. When Status LED is flashing red, remove the bind plug, so that the Status LED will flash slowly. Now remove power and connect your EXBUS receiver to the SYS port. Power up again, NANOBEAST should recognize the receiver and start with init sequence now. After init you can perform the setup using your JETI radio's JETIBox menu. If needed, you can connect the BLE2SYS or USB2SYS adapter later at anytime to the SYS connector, i.e. to perform firmware update, by removing the receiver when the system is off. When the receiver is not detected during power up within 5 seconds, the NANOBEAST will be available for normal SYS operation.

Setup with StudioX

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the Control menu in StudioX and click the SCAN button in this menu's screen. Please note that when the EXBUS receiver is connected to SYS port on MICROBEAST PLUS / ULTRA, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port using the optional adapter from standard servo connector to 5-pin JST. For further informations please refer to the StudioX instruction notes.

(Picture sys adapter!)

With NANOBEAST it's not possible to scan the receiver type from StudioX when the receiver is connected at this. Here the receiver will can be bound by using the bind plug as shown above.