Manuals:MBUltraFblV5:TelemetryInfo/de: Difference between revisions
Shornstein (talk | contribs) No edit summary |
Updating to match new version of source page |
||
| Line 35: | Line 35: | ||
<br /> | <br /> | ||
<div class="mw-translate-fuzzy"> | |||
= FRSky F.Port2 = | = FRSky F.Port2 = | ||
Make sure you receiver is set up to send data in F.Port2 data format. Usually this is done from the MODEL MENU of your FRSky radio.<br /> | Make sure you receiver is set up to send data in F.Port2 data format. Usually this is done from the MODEL MENU of your FRSky radio.<br /> | ||
| Line 51: | Line 52: | ||
|}<br /> | |}<br /> | ||
<br /> | <br /> | ||
</div> | |||
= Futaba SBUS2 = | = Futaba SBUS2 = | ||
Revision as of 11:18, 19 June 2023
Für die Anzeige der Telemetriedaten müssen im Fernsteuersender üblicherweise einige Einstellungen vorgenommen werden. Hier beschreiben wir die grundlegenden Schritte, wie die Telemetrieanzeige auf verschiedenen Fernsteuerungen aktiviert wird. Weitere Informationen zum Einrichten von Alarmen und anderen Optionen findest Du in der Bedienungsanleitung der Fernsteuerung.
JETI EXBUS
SPEKTRUM SRXL2
GRAUPNER HOTT
Make sure you receiver is set up to send telemetry data on the external telemetry data output. Usually this is done from the TELEMETRY MENU of your HOTT radio.
The telemetry data line is connected to [SYS] port of MICROBEAST ULTRA. For this type of application you must set RECEIVER MENU point L to Status LED blue (="HOTT").
See section "Telemetry" in RECEIVER MENU for additional information.
To get telemetry information on your radio's display, there is not much to do. Just make sure to switch on the radio and receiver simultaneously. If you open the TELEMETRY tab on the radio you should see the "SEARCH" label, indicating that telemetry data received by the radio. After apprx. 15 seconds, the radio should display telemetry data. MICROBEAST ULTRA is simulating a HOTT EAM (Electric Air Module) and VARIO. So you will see the associated screens on the radio.
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
FRSky F.Port2
Make sure you receiver is set up to send data in F.Port2 data format. Usually this is done from the MODEL MENU of your FRSky radio.
If telemetry data is received, you should see all available data when starting the SCAN PROCESS in TELEMETRY MENU of your FRSky radio.
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
.jpg)
|
Futaba SBUS2
Make sure you receiver is set up to send SBUS2 telemetry data. Usually this is done from the LINKAGE MENU of your Futaba radio. Sometimes it is necessary to perform a rebind, in order to activate the telemetry output!
In the SENSOR menu activate the following devices:
- SLOT 8: rpm sensor (=headspeed)
- SLOTs 9-10-11: CUR-1678 (=voltage, current, consumption)
- SLOT 12: TEMP-1713 (=ESC temperature)
- SLOT 13: TEMP-1713 (=PWM)
.jpg)
|
.jpg)
|
Please note this assignment is fixed. If you use additional sensors on the same slots, these must be reassigned to other slots.
You can add alarms to each item in the TELEMETRY menu. Please refer to the instructions manual of your radio for further reference.