Changes

=Spektrum® SRXL2 receiver= <!--T:7-->

=Spektrum® SRXL2 receiver= <!--T:7-->

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as reeceivers with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />

Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. Anyways, the output signal of those receiver must always be connected to the pin board at the side of MICROBEAST PLUS.<br />

<br />

<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />

When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />

<br />

<br />

In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!<br />

In order to connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 AR6610T en.png| x150px]]

|[[Image:SRXL2 AR6610T en.png| x150px]]

| SRXL2 receiver with standard servo connector and adapter

| SRXL2 receiver with standard servo connector and adapter

|}

|}

In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 Satellite en.png| x180px]]

|[[Image:SRXL2 Satellite en.png| x180px]]

| SRXL2 satellite receiver with modified satellite connector

| SRXL2 satellite receiver with modified satellite connector

|}

|}

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 Satellite wrong en.png| x120px]]

|[[Image:SRXL2 Satellite wrong en.png| x120px]]

|[[Image:SRXL2 Satellite correct en.png| x120px]]

|[[Image:SRXL2 Satellite correct en.png| x120px]]

|}<br />

|}<br />

<br />

<br />

</translate>

</translate>