Changes

=Receivers with single wire output= <!--T:5-->

=Receivers with single wire output= <!--T:5-->

A single-line receiver transmits all channels/all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all stick outputs to a digital data paket or by chaining the signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBUS, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM.<br />

A single-line receiver transmits all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all channel outputs into a digital data paket or by chaining the signals onto one line.<br />

MICROBEAST PLUS supports the following systems '''with telemetry uplink''':

* Spektrum® SRXL2

* JETI® EXBUS

<br />

<br />

(For Spektrum® SRXL2 or when you like to make use of telemetry data, please connect your receiver as shonw under [[#Spektrum® SRXL2 / JETI EXBUS receivers for telemetry]].)<br />

MICROBEAST PLUS supports the following systems '''without telemetry''':

* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output

* any SPPM (serial ppm) receiver .<br />

<br />

<br />

<!--T:9-->

<!--T:9-->

* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS

* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS

* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.

* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.

* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.<br />

* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD|PIT|AUX]; please do not connect anything here!).<br />

<br />

<br />

{|cellspacing="20" style="text-align:center;"

{|cellspacing="20" style="text-align:center;"

<br />

<br />

=Remote satellite (Spektrum® DSM/JR® DMSS/ALIGN® iBus)= <!--T:6-->

<!--T:6-->

A special type of single-line receiver is the remote satellite. These receivers usually serve as additional receiving unit in combination with a (bigger) main receiver to provide a more robust and fail safe radio system. With MICROBEAST PLUS you can use such receivers as stand alone receiving unit to achieve a small and light weight radio system for small sized rc models. MICROBEAST PLUS supports the following systems: Spektrum® DSM2, Spektrum® DSMX, JR® DMSS and ALIGN® iBus. The remote receiver can be directly connected to the white pin board at the side of MICROBEAST PLUS. Here the receiver will be powered with a stabilized voltage of 3.3 Volts. Alternatively if you own the optional available Spektrum® satellite adapter (Order Nr. BXA76009) you can connect the receiver at the front pin board to the [DI1] digital input, just like most other single-wire receivers. This allows to keep the white pin board free for connecting a sensor.<br />

Remote receivers (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, minus is the second pin from the right, signal is connected at the third pin from the right.<br />

<br />

<br />

'''Please note:''' MICROBEAST PLUS does not support connecting more than one remote satellite at a time!<br />

'''Please note:''' MICROBEAST PLUS does not support connecting more than one remote satellite at a time!<br />

|}

|}

<br />

<br />

{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc models (helicopters of 450 size or smaller).''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range!}}<br />

{{WARNING_QUOTE|'''Using a remote satellite is only recommended for small rc modells like helicopters of 450 size or smaller.''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range.}}<br />

<br />

<br />

<br />

<br />

=Telemetry receivers Spektrum® SRXL2 / JETI EXBUS= <!--T:7-->

<!--T:7-->

'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />

Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />

To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 AR6610T en.png| x150px]]

|[[Image:SRXL2 AR6610T en.png| x150px]]

|}

|}

<br />

<br />

<br />

<br />

To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

To connect a SRXL2 remote receiver like '''SPM4650/SPM4651T''' it is necessary to '''INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

{|cellspacing="50" style="text-align:center;"

{|cellspacing="50" style="text-align:center;"

|[[Image:SRXL2 Satellite en.png| x180px]]

|[[Image:SRXL2 Satellite en.png| x180px]]

| Modified 4-pin SRXL connector

| Modified 4-pin SRXL connector

|}

|}

{{WARNING_QUOTE|'''Never connect the 4-pin receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />

{{WARNING_QUOTE|'''Never connect the 4-pin receiver connector to MICROBEAST ULTRA without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />

<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />

<br />

<br />

<br />

<br />

</translate>

</translate>