Changes

<br />

<br />

SBUS was one of the first serial data signal protocols. The receiver sends out control signals from the radio in data packets which the flybarless system can decode and use as control commands. This protocol is so popular that other manufacturers are using it as well, i.e. FRSKY receivers. So you don't need to have a Futaba radio system for using SBUS. Please note that the channel assignment of your radio can be different to the Futaba standard though. In this case you must teach a user defined channel assignment during in the BEASTX receiver menu later.

'''SBUS''' was one of the first serial data signal protocols. The receiver sends out control signals from the radio in data packets which the flybarless system can decode and use as control commands. This protocol is so popular that other manufacturers are using it as well, i.e. FRSKY receivers. So you don't need to have a Futaba radio system for using SBUS. Please note that the channel assignment of your radio can be different to the Futaba standard though. In this case you must teach a user defined channel assignment during in the BEASTX receiver menu later.<br />

SBUS2 is the successor of SBUS. Basically it is the same protocol as SBUS but enhanced by bi-directional telemetry communication. With the BEASTX devices you can connect the SBUS2 port to the same port as SBUS. The system will accept this signal as well. With MICROBEAST ULTRA you can take advantage of bidirectional communication. Here you must connect the SBUS2 signal to one of the bidrectional ports: DI2 or SYS.

'''SBUS2''' is the successor of SBUS. Basically it is the same protocol as SBUS but enhanced by bi-directional telemetry communication. With the BEASTX devices you can connect the SBUS2 port to the same port as SBUS. The system will accept this signal as well. Using MICROBEAST ULTRA you can take advantage of bi-directional communication. Here you must connect the SBUS2 signal to one of the bi-directional ports: DI2 or SYS.<br />

Signal Port Telemetry

 

SBUS DI1 no

 

! style="width: 100px" | Signal  

SBUS2 DI1 no

! style="width: 100px" | Port

 

! style="width: 200px" | Telemetry

SBUS2 SYS yes only MB ULTRA

 

| SBUS || DI1 || no

SBUS2 DI2 yes only MB ULTRA

| SBUS2 || DI1 || no

| SBUS2 || SYS || yes (only MB ULTRA)

| SBUS2 || DI2 || yes (only MB ULTRA)

=SBUS / SBUS2 (radio control only)=

=SBUS / SBUS2 (radio control only)=

(Picture MBPLUS)

(Picture MBPLUS)

(Picture Nanobeast)

(Picture Nanobeast)<br />

=SBUS2 with telemetry=

=SBUS2 with telemetry=

(Picture Resistor)

(Picture Resistor)

(Picture DI2)

(Picture DI2)<br />

=Radio setup=

=Radio setup=

Telemetry....

Telemetry....<br />

=BEASTX setup=

=BEASTX setup=

In order to use your SBUS/SBUS2 receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device.

In order to use your SBUS / SBUS2 receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering

for your radio system.<br />

==MICROBEAST PLUS / MICROBEAST ULTRA==

==MICROBEAST PLUS / MICROBEAST ULTRA==

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence.

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence.

For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.

For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

==NANOBEAST==

==NANOBEAST==

Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.

Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

==Setup with StudioX==

==Setup with StudioX==

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />

 

 

 

</translate>

</translate>