Changes

|+ style="caption-side:bottom;"|SBUS / SBUS2 connection options

|+ style="caption-side:bottom;"|SBUS / SBUS2 connection options

|-

|-

! style="width: 100px;" | Signal  

! style="width: 100px; background-color: #f4bf9e" | Signal  

! style="width: 100px;"  | Port

! style="width: 100px; background-color: #f4bf9e"  | Port

! style="width: 200px;"  | Telemetry

! style="width: 200px; background-color: #f4bf9e"  | Telemetry

|-

|-

| SBUS || DI1 || no

| SBUS || DI1 || no

| SBUS2 || DI2 || yes (only MB ULTRA)

| SBUS2 || DI2 || yes (only MB ULTRA)

|}

|}

<br />

<br />

=SBUS / SBUS2 (radio control only)=

=SBUS / SBUS2 - control only=

Using SBUS/SBUS2 to control your helicopter is possible with any of the BEASTX devices. Connect the SBUS/SBUS2 port of your receiver with the DI1 port of your BEASTX system using one of the provided standard servo wires.<br />

Using SBUS/SBUS2 to control your helicopter is possible with any of the BEASTX devices. Connect the SBUS/SBUS2 port of your receiver with the DI1 port of your BEASTX system using one of the provided standard servo wires.<br />

<br />

<br />

(Picture Nanobeast)<br />

(Picture Nanobeast)<br />

<br />

<br />

=SBUS2 with telemetry=

=SBUS2 - control and telemetry=

For bi-directional telemetry connect your SBUS2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST ULTRA. In both cases it is mandatory to add a pull-down 4,7kOhm resistor between signal line and ground (minus). When using the DI2 port, also you need an adapter from standard servo connector to 5-pin JST as shown below.

For bi-directional telemetry connect your SBUS2 signal wire either to the SYS port or to the DI2 port of your MICROBEAST ULTRA. In both cases it is mandatory to add a pull-down 4,7kOhm resistor between signal line and ground (minus). When using the DI2 port, also you need an adapter from standard servo connector to 5-pin JST as shown below.

(Picture Resistor)

(Picture Resistor)

(Picture DI2)<br />

(Picture DI2)<br />

<br />

<br />

=Radio setup=

=Radio setup=

Telemetry....<br />

Telemetry....<br />

<br />

<br />

|+ style="caption-side:bottom;|SBUS / SBUS2 default channel order

|+ style="caption-side:bottom;|SBUS / SBUS2 default channel order

|-

|-

! style="width: 100px" | Channel

! style="width: 100px; background-color: #f4bf9e" | Channel

! style="width: 200px" | Function

! style="width: 200px; background-color: #f4bf9e" | Function

|-

|-

| CH1 || Roll / Aileron

| CH1 || Roll / Aileron

| CH9 || Aux channel (optional)

| CH9 || Aux channel (optional)

|}

|}

(The optional functions are described in the section '''Optional features'''.)<br />

''(The optional functions are described in the section '''Optional features'''.)''<br />

<br />

<br />

<br />

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence.

Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menu LEDs L & M, if applicable; push button briefly to skip. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence.

For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

<br />

<br />

==NANOBEAST==

==NANOBEAST==

Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

Power up NANOBEAST. Then connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />

<br />

<br />

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />

You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />

<br />

<br />

<br />

<br />

</translate>

</translate>