Changes

* The assignment for CH6 Output can be skipped by pressing the button without teaching a channel for this function in case it is not used.

* The assignment for CH6 Output can be skipped by pressing the button without teaching a channel for this function in case it is not used.

* Likewise, the assignment of the channel for nitro RPM Governor can be skipped in case it is not needed or if you don‘t want to control the RPM Governor by a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the RPM Governor function will use a different operating mode that allows to control it via the throttle channel (set at menu point '''G''') if you like. When used in an electric model the RPM Governor generally is controlled via the throttle channel (set at menu point '''G'''). In this case the assignment at menu point I can be skipped  anyway, as an assignment will have no effect.

* Likewise, the assignment of the channel for nitro RPM Governor can be skipped in case it is not needed or if you don‘t want to control the RPM Governor by a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the RPM Governor function will use a different operating mode that allows to control it via the throttle channel (set at menu point '''G''') if you like. When used in an electric model the RPM Governor generally is controlled via the throttle channel (set at menu point '''G'''). In this case the assignment at menu point I can be skipped  anyway, as an assignment will have no effect.

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:Flying|using AttitudeControl]] for further details.<br />

* Finally at menu point '''J''' you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point '''F''') is also used to switch AttitudeControl, see the section about [[Manuals:MB_Plus:AttitudeControl_usage/en|using AttitudeControl]] for further details.<br />

<br />

<br />

{{QUOTE|* If the Status-LED stays red at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

{{QUOTE|* If the Status-LED stays red at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected at [[Manuals:MB_Plus:Receiver_setup_menu_A/en|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N|Setup menu point N]] and [[Manuals:MB_Plus:Parametermenu_L|Parameter menu point L]]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}<br />

* Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points ([[Manuals:MB_Plus:Setupmenu_N/en|Setup menu point N]] and [[Manuals:MB_Plus:Parametermenu_L/en|Parameter menu point L]]). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.}}<br />

<br />

<br />

----

----

After the last menu point for channel assignment by pressing the button the Menu-LED jumps directly to [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''N''']] for throttle failsafe setting.

After the last menu point for channel assignment by pressing the button the Menu-LED jumps directly to [[Manuals:MB_Plus:Receiver_setup_menu_N/en|Receiver menu point '''N''']] for throttle failsafe setting.

----

----

</translate>

</translate>