7,261
edits
Changes
Jump to navigation
Jump to search
Line 45:
Line 45: − <span style="font-size: 13px;">**AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls ''CH6 Output''.<br /></span> − <span style="font-size: 13px;">***Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span> − + + + + − '''In case the ordering differs from the given tables, you have to manually assign the channel order step by step. How this works is described below.'''<br />+ − +
Manuals:MB Plus:Receiver setup menu B/en (view source)
Revision as of 13:03, 10 June 2015
, 8 years agoImporting a new version from external source
|THROTTLE || AILERON || ELEVATOR || RUDDER || GEAR || AUX1 || AUX2 || AUX3 || AUX4
|THROTTLE || AILERON || ELEVATOR || RUDDER || GEAR || AUX1 || AUX2 || AUX3 || AUX4
|}
|}
<br />
<br />
To load the preset channel assignment wait until the Status-LED lights blue and then hold down the button for several seconds. The yellow Menu-LED will immediately jump to [[Manuals:MB_Plus:Receiver_setup_A|Receiver menu point '''N''']].<br />
<span style="font-size: 13px;">**AttitudeControl only applicable with MICROBEAST PLUS ProEdition firmware. When using a different firmware this channel by default controls CH6 Output.<br /></span>
<span style="font-size: 13px;">***Only applicable when RPM Governor feature is installed. Please note that the separate RPM Governor control is only used for nitro helicopters. The RPM Governor for electric helis always uses the throttle channel for governor control.<br /></span><br />
<br />
To load the preset channel assignment wait until the Status-LED lights <font color="#0066FF">'''blue'''</font> and then hold down the button for several seconds. The yellow Menu-LED will immediately jump to [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''N''']].<br />
<br />
<br />
[[File:Channel_assignment.png|x200px|none]]
[[File:Channel_assignment.png|x200px|none]]
<br />
<br />
In case the ordering differs from the given tables, you have to manually assign the channel order step by step. How this works is described below.<br />
<br />
<br />
{{QUOTE|* If the Status-LED stays red at menu point B, this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.<br />
{{QUOTE|* If the Status-LED stays '''red''' at menu point '''B''', this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly [[Manuals:MB_Plus:Receiver_Installation/en#Receiver_binding|bound to the transmitter]] and that a receiver/transmission protocol of the correct type is selected in [[Manuals:MB_Plus:Receiver_setup_menu_A|Receiver menu point '''A''']]. Switch off the power and restart the receiver type setup procedure from the beginning.<br />
* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}<br />
* You can also load the default assignment by pushing the button for several seconds in any of the following points for function assignment. This will erase all previously made individual assignments.}}<br />
<br />
<br />