Manuals:MBPlusFblV52:Setupmenu M: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
← Older edit
No edit summary
No edit summary
 
(5 intermediate revisions by the same user not shown)
Line 2: Line 2:
<!--T:1-->
<!--T:1-->
{{DISPLAYTITLE:SETUP MENU M - Servo limit|noerror}}
{{DISPLAYTITLE:SETUP MENU M - Servo limit|noerror}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV52:Setupmenu_K/en|Manuals:MBPlusFblV52:Setupmenu_M/en|SETUPMENU|2}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV52:Setupmenu_L/en|Manuals:MBPlusFblV52:Governor/en|SETUPMENU|2}}
__TOC__
__TOC__
<br />
<br />


<!--T:2-->
<!--T:2-->
At SETUP MENU point M we can limit the servo movement so that the servos will not come out of the possible range of action and cause jamming of the linkages or swashplate. But ideally we want to limit as less as possible, so that the system can control the helicopter without any restrictions!
At SETUP MENU point '''M''' we can limit the servo movement so that the servos will not come out of the possible range of action and cause jamming of the linkages or swashplate. But ideally we want to limit as less as possible, so that the system can control the helicopter without any restrictions! For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible directions at once, especially when steering into the corners.<br />
<br />
For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible positions at once, especially when steering into the corners. So when adjusting the limit, you move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. Adjust the limit so that there is just no binding at any point.<br />
<br />
<br />
The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all.<br />
The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all.<br />
Line 25: Line 23:


<!--T:6-->
<!--T:6-->
{{QUOTE|* Always try to give the system as much servo throw as possible and limit as less as possible. Do not use the limit to adjust the pitch or rates or similar, this is not what it is it used for!
{{WARNING_QUOTE| Always try to give the system as much servo throw as possible and limit as less as possible. Do not use the limit to adjust the pitch or rates or similar, this is not what it is it used for!}}<br />
* When changing the collective pitch later this may affect the cyclic limit, so don't forget to check and readjust the limit when you do any changes to the collective.}}<br />
<br />
<br />
<br />


=Adjustment on the device= <!--T:3-->
=Adjustment on the device= <!--T:3-->
At SETUP MENU point L carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. By '''rudder''' stick input you can '''increase/decrease the amount of maximum servo throw/servo limit''' (left = decrease throw, right = increase throw). Make sure the throw is as high as possible.<br />
* At SETUP MENU point '''M''' carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed.
* By '''rudder''' stick input you can '''increase/decrease the amount of maximum servo throw/servo limit''' (left = decrease throw, right = increase throw).
* Make sure the throw is as high as possible.  
* If you change the collective pitch at SETUP MENU point '''L''' at a later time, check and readjust the cyclic limit if necessary!<br />
<br />
<br />
<br />
<br />


=Setup with StudioXm= <!--T:5-->
=Setup with StudioX app= <!--T:5-->
Carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. Increase/decrease the amount of maximum servo throw/servo limit by using the '''+''' and '''- buttons''' and the '''dial'''. Make sure the value is as high as possible.<br />
* Carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed.
* Increase/decrease the amount of maximum servo throw/servo limit by using the '''+''' and '''- buttons''' and the '''dial'''.
* Make sure the value is as high as possible.
* If you change the collective pitch at SETUP MENU point '''L''' at a later time, check and readjust the cyclic limit if necessary!<br />
<br />
<br />
[[File:SetupLm.PNG|x250px]]<br />
[[File:Basic_setup_cyclic_limit.PNG|x250px]]<br />
<br />
<br />
<br />
<br />


</translate>
</translate>

Latest revision as of 10:48, 1 March 2023

MICROBEAST PLUS V5

1. Introduction

2. Safety notes

3. Box content and accessories

4. Hardware installation

5. Receiver connection

6. Radio system

7. Receiver Menu
Receiver type
Function assignment
Telemetry input
Throttle failsafe
8. Basic setup
Device orientation
Swashplate servos
Rudder pulse width
Rudder frequency
Rudder control
Swash mixing
Servo directions
Cyclic directions
Servo trim
Cyclic throw
Collective pitch
Servo limit
9. Headspeed Governor
Activating the governor
Sensor test mode
Throttle low position
Throttle high position
Transmitter setup
Signal divider
Main gear ratio
10. Parameters
Trimming
Control style
Special parameters
11. Special features
AttitudeControl (Self leveling)


Bank Switching
Tail motor

12. Factory reset

13. Version information

15. Firmware update

← →


At SETUP MENU point M we can limit the servo movement so that the servos will not come out of the possible range of action and cause jamming of the linkages or swashplate. But ideally we want to limit as less as possible, so that the system can control the helicopter without any restrictions! For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible directions at once, especially when steering into the corners.

The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all.

Status-LED Servo limit
purple not good
red OK
blue perfect!



Always try to give the system as much servo throw as possible and limit as less as possible. Do not use the limit to adjust the pitch or rates or similar, this is not what it is it used for!



Adjustment on the device

  • At SETUP MENU point M carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed.
  • By rudder stick input you can increase/decrease the amount of maximum servo throw/servo limit (left = decrease throw, right = increase throw).
  • Make sure the throw is as high as possible.
  • If you change the collective pitch at SETUP MENU point L at a later time, check and readjust the cyclic limit if necessary!



Setup with StudioX app

  • Carefully move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed.
  • Increase/decrease the amount of maximum servo throw/servo limit by using the + and - buttons and the dial.
  • Make sure the value is as high as possible.
  • If you change the collective pitch at SETUP MENU point L at a later time, check and readjust the cyclic limit if necessary!





Retrieved from "https://wiki.beastx.com/index.php?title=Manuals:MBPlusFblV52:Setupmenu_M&oldid=20915"