Manuals:MBPlusFblV52:Box Content/de: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
← Older editNewer edit →
No edit summary
Created page with "= MICROBEAST PLUS = <br /> {| |- style="vertical-align:bottom;" |none|x250px<br /> | * MICROBEAST PLUS Steuereinheit * gedruckte Schnellstart..."
Line 3: Line 3:
<br />
<br />


= This is what you get when buying the MICROBEAST PLUS =
= MICROBEAST PLUS =
<br />
<br />
{|
{|
Line 9: Line 9:
|[[File:Box contents mbplus.png|none|x250px]]<br />
|[[File:Box contents mbplus.png|none|x250px]]<br />
|  
|  
* the MICROBEAST PLUS flybarless unit
* MICROBEAST PLUS Steuereinheit
* printed Quickstart manual, Quick reference card and BEASTX sticker set
* gedruckte Schnellstartanleitung, Übersichtskarte und einige BEASTX sticker
* all the wires to connect your receiver to the system (wire length 150mm)
* alle notwendigen Kabel um einen Fernsteuerempfänger am System anschließen zu können (Länge 150mm)
* 3M gyro pads
* 3M Klebepads zur Befestigung
* plastic tool for adjusting the gain dials
* Kunststoffwerkzeug zum Drehen der Gain Potis am Gerät
<br />
<br />
|}
|}
'''Please note:''' MICROBEAST PLUS is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.<br />
'''Hinweis:''' Das MICROBEAST PLUS wird üblicherweise mit der BASIS Firmware ausgeliefert. Du kannst es später jederzeit über die StudioX PC Software oder die StudioXm App zur PROEDITION hochstufen. Falls gewünscht, frag Deinen Händler, ob er das MICROBEAST PLUS direkt als PROEDITION liefern kann.<br />
<br />
<br />
<br />
<br />

Revision as of 10:38, 13 April 2021

MICROBEAST PLUS V5

1. Introduction

2. Safety notes

3. Box content and accessories

4. Hardware installation

5. Receiver connection

6. Radio system

7. Receiver Menu
Receiver type
Function assignment
Telemetry input
Throttle failsafe
8. Basic setup
Device orientation
Swashplate servos
Rudder pulse width
Rudder frequency
Rudder control
Swash mixing
Servo directions
Cyclic directions
Servo trim
Cyclic throw
Collective pitch
Servo limit
9. Headspeed Governor
Activating the governor
Sensor test mode
Throttle low position
Throttle high position
Transmitter setup
Signal divider
Main gear ratio
10. Parameters
Trimming
Control style
Special parameters
11. Special features
AttitudeControl (Self leveling)


Bank Switching
Tail motor

12. Factory reset

13. Version information

15. Firmware update

← →


MICROBEAST PLUS
  • MICROBEAST PLUS Steuereinheit
  • gedruckte Schnellstartanleitung, Übersichtskarte und einige BEASTX sticker
  • alle notwendigen Kabel um einen Fernsteuerempfänger am System anschließen zu können (Länge 150mm)
  • 3M Klebepads zur Befestigung
  • Kunststoffwerkzeug zum Drehen der Gain Potis am Gerät


Hinweis: Das MICROBEAST PLUS wird üblicherweise mit der BASIS Firmware ausgeliefert. Du kannst es später jederzeit über die StudioX PC Software oder die StudioXm App zur PROEDITION hochstufen. Falls gewünscht, frag Deinen Händler, ob er das MICROBEAST PLUS direkt als PROEDITION liefern kann.


This is what you get when buying the MICROBEAST PLUS HD


  • the MICROBEAST PLUS HD flybarless unit
  • printed Quickstart manual, Quick reference card and BEASTX sticker set
  • all the wires to connect your receiver to the system (wire length 150mm)
  • 3M gyro pads
  • plastic tool for adjusting the gain dials
  • high power connector and on/off switch



Please note: MICROBEAST PLUS HD is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.


Optional accessory


USB2SYS



USB2SYS connects your MICROBEAST PLUS / MICROBEAST PLUS HD with your computers USB port. With the StudioX Software (available for Windows and macOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more.

For more information please see the StudioX manual.

BLE2SYS



BLE2SYS is a Bluetooth Smart Interface that allows to connect your MICROBEAST PLUS / MICROBEAST PLUS HD to your smartphone or tablet. With the StudioXm app (available for Android and iOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more. Please note that your mobile device must be Bluetooth Smart/Bluetooth LE compatible.

For more information please see the StudioXm manual.


Retrieved from "https://wiki.beastx.com/index.php?title=Manuals:MBPlusFblV52:Box_Content/de&oldid=18371"