Difference between revisions of "Manuals:BXFbl:Setupmenu overview"

From BEASTX Wiki
Jump to navigation Jump to search
(Created page with "<translate> <!--T:1--> {{DISPLAYTITLE:SETUP MENU overview|noerror}} {{TOC_BXFbl|Manuals:BXFbl:Setupmenu_intro/en|Manuals:BXFbl:Setupmenu_A/en|SETUPMENU|}} __TOC__ <br /> Here...")
 
Line 3: Line 3:
 
{{DISPLAYTITLE:SETUP MENU overview|noerror}}
 
{{DISPLAYTITLE:SETUP MENU overview|noerror}}
 
{{TOC_BXFbl|Manuals:BXFbl:Setupmenu_intro/en|Manuals:BXFbl:Setupmenu_A/en|SETUPMENU|}}
 
{{TOC_BXFbl|Manuals:BXFbl:Setupmenu_intro/en|Manuals:BXFbl:Setupmenu_A/en|SETUPMENU|}}
−
__TOC__
+
__NOTOC__
 
<br />
 
<br />
  
Line 10: Line 10:
  
 
On MICROBEAST PLUS / ULTRA the current menu step is indicated by the LED letters. In SETUP MENU the menu LED must light constantly. If it's flashing, you're in the wrong menu!<br />
 
On MICROBEAST PLUS / ULTRA the current menu step is indicated by the LED letters. In SETUP MENU the menu LED must light constantly. If it's flashing, you're in the wrong menu!<br />
 +
<br />
 +
 
With NANOBEAST the current menu step is indicated by number of flashes of the Status LED. In Setup Menu the Status LED will flash in blue color. Steps A to G are indicated by 1 to 7 flashes. From steps H to M onwards again there will be 1 to 7 flashes to indicate the current menu step. But here the first flash will be long.<br />
 
With NANOBEAST the current menu step is indicated by number of flashes of the Status LED. In Setup Menu the Status LED will flash in blue color. Steps A to G are indicated by 1 to 7 flashes. From steps H to M onwards again there will be 1 to 7 flashes to indicate the current menu step. But here the first flash will be long.<br />
 +
<br />
 
<br />
 
<br />
  
Line 30: Line 33:
 
         table#overview tr td:nth-child(10)
 
         table#overview tr td:nth-child(10)
 
         {  
 
         {  
−
             width: 70px;
+
             width: 100px;
 
         }
 
         }
 
     </style>
 
     </style>
Line 47: Line 50:
 
! blue
 
! blue
 
! red/blue alternating
 
! red/blue alternating
−
|-
+
|- style="font-size: 80%;"
−
| A || Device orientation || horizontal, pins to front || vertical, pins to front || hor. inv., pins to front || vert. inv., pins to front || horizontal, pins to back || vertical, pins to back || hor. inv., pins to back || vert. inv., pins to back
+
| style="font-size: 125%;" | A || style="font-size: 125%;" | Device orientation || horizontal, pins to front || vertical, pins to front || hor. inv., pins to front || vert. inv., pins to front || horizontal, pins to back || vertical, pins to back || hor. inv., pins to back || vert. inv., pins to back
 
|-
 
|-
 
| B || Swashplate servos || custom || style = "background-color: #EAECF0;" | || 50 Hz || 65 Hz || 120 Hz || 165 Hz || 200 Hz || style = "background-color: #EAECF0;" |
 
| B || Swashplate servos || custom || style = "background-color: #EAECF0;" | || 50 Hz || 65 Hz || 120 Hz || 165 Hz || 200 Hz || style = "background-color: #EAECF0;" |
Line 76: Line 79:
 
| N || Governor || off || colspan = "3" style = "background-color: #EAECF0;" | || electric heli || style = "background-color: #EAECF0;" | || nitro heli || style = "background-color: #EAECF0;" |
 
| N || Governor || off || colspan = "3" style = "background-color: #EAECF0;" | || electric heli || style = "background-color: #EAECF0;" | || nitro heli || style = "background-color: #EAECF0;" |
 
|}
 
|}
 +
<br />
 +
<br />
 +
 +
 +
= A - Device orientation =
 +
<br />
 +
<br />
 +
 +
= B - Swashplate servos =
 +
<br />
 +
<br />
 +
 +
= C - Rudder pulse width =
 +
<br />
 +
<br />
 +
 +
= D - Rudder frequency =
 +
<br />
 +
<br />
 +
 +
= E - Rudder limit =
 +
<br />
 +
<br />
 +
 +
= F - Rudder direction =
 +
<br />
 +
<br />
 +
 +
= G - Swash mixing =
 +
<br />
 +
<br />
 +
 +
= H - Servo directions =
 +
<br />
 +
<br />
 +
 +
= I - Cyclic directions =
 +
<br />
 +
<br />
 +
 +
= J - Servo trim =
 +
<br />
 +
<br />
 +
 +
= K - Cyclic throw =
 +
<br />
 +
<br />
 +
 +
= L - Collective pitch =
 +
<br />
 +
<br />
 +
 +
= M - Servo limit =
 +
<br />
 +
<br />
 +
 +
= N - Governor =
 +
<br />
 +
<br />
 +
 
<br />
 
<br />
  
 
</translate>
 
</translate>

Revision as of 08:14, 19 April 2024

BeastX FBL

1. Introduction

2. Safety notes

3. Hardware installation

4. Radio setup
Futaba SBUS / SBUS2
Jeti EXBUS
SRXL / SUMD / XBUS
Spektrum SRXL2
ExpressLRS / CRSF
FRSKY SPort / FPort
Standard PPM
Serial PPM
5. Receiver Menu
Receiver type
Function assignment
Telemetry input
Throttle failsafe
6. Basic setup
Overview
Device orientation
Swashplate servos
Rudder pulse width
Rudder frequency
Rudder control
Swash mixing
Servo directions
Cyclic directions
Servo trim
Cyclic throw
Collective pitch
Servo limit
7. Headspeed Governor
Activating the governor
Sensor test mode
Throttle low position
Throttle high position
Transmitter setup
Signal divider
Main gear ratio
8. Parameters
Gain adjustment
Trimming
Control style
Special parameters
9. Optional features
AttitudeControl (setup)
AttitudeControl (usage)
Bank Switching
Telemetry

10. Factory reset

11. Version information

12. Firmware update

← →


Here is an overview and a short description of the setup procedure. You will get more details about each menu step in the following sections.

On MICROBEAST PLUS / ULTRA the current menu step is indicated by the LED letters. In SETUP MENU the menu LED must light constantly. If it's flashing, you're in the wrong menu!

With NANOBEAST the current menu step is indicated by number of flashes of the Status LED. In Setup Menu the Status LED will flash in blue color. Steps A to G are indicated by 1 to 7 flashes. From steps H to M onwards again there will be 1 to 7 flashes to indicate the current menu step. But here the first flash will be long.


SETUP MENU overview

Menu Description off purple flashing purple red flashing red blue flashing blue red/blue alternating
A Device orientation horizontal, pins to front vertical, pins to front hor. inv., pins to front vert. inv., pins to front horizontal, pins to back vertical, pins to back hor. inv., pins to back vert. inv., pins to back
B Swashplate servos custom 50 Hz 65 Hz 120 Hz 165 Hz 200 Hz
C Rudder pulse width custom 760 µs 960 µs 1520 µs
D Rudder frequency custom 50 Hz 165 Hz 270 Hz 333 Hz 560 Hz
E Rudder limit limit left limit right
F Rudder direction left right
G Swash mixing custom no mixing 90°(3/4 servos) 120° 140° 135°/140°(1:1)
H Servo directions Servo 1 Servo 2 Servo 3 (Servo 4)
I Cyclic directions left/back right/forward
J Servo trim neutral Servo 1 Servo 2 Servo 3 (Servo 4)
K Cyclic throw neutral Adjust to 6°
L Collective pitch min MAX
M Servo limit Don't fly not good OK perfect!
N Governor off electric heli nitro heli




A - Device orientation



B - Swashplate servos



C - Rudder pulse width



D - Rudder frequency



E - Rudder limit



F - Rudder direction



G - Swash mixing



H - Servo directions



I - Cyclic directions



J - Servo trim



K - Cyclic throw



L - Collective pitch



M - Servo limit



N - Governor




Retrieved from "https://wiki.beastx.com/index.php?title=Manuals:BXFbl:Setupmenu_overview&oldid=23044"