Manuals:BXFbl:Setupmenu L/en/en

At SETUP MENU point L you set the maximum negative and positive collective pitch for your helicopter. Additionaly you have to make sure the BEASTX system is detecting the pitch correctly. This especially is important when using the rescue bailout function (but has also effect on the normal flying)!

Don't modify the pitch curves in your radio when doing the collective adjustments! Let everything at default (i.e. -100 +0 +100), so the stick is moving the thrust channel over the full range. When finished, you can adjust your collective pitch curves in the radio as you like and as you are used to. But for now, we need to set the full working range which is necessary to gain optimum performance.

At this step it is important to define the mechanical possible range of your helicopter, not to define your flying style. For example, when using a 3D trainer helicopter frame, this usually will have a symmetric pitch range, i.e. reaching from +12 to -12 degrees. Now when you are a beginner or scale pilot you would not need that high amount of pitch (especially not in the negative section). Anyhow, it is not recommended to set the pitch range asymmetrical to -4 to +12 degrees for example, as this would not represent the helicopters capability. Better is to set the endpoints to -12 and +12 degrees. Later use the pitch curves in your radio to adjust the negative pitch to your preferred flying style. Have a look in your helicopter's manual to find out what is the optimum pitch range.

Adjustment on the device

1. Move the thrust stick up and down and check whether the pitch is changing direction correctly. If not already done at SETUP MENU point H, use the reverse function for the collective pitch channel in the radio to reverse direction of pitch movement, in case it is wrong.

2. Afterwards check the Status LED color: on positive pitch it must be blue, on negative pitch it must light in red color. In case the display is inverted (red = positive and blue = negative), tap the rudder stick once to reverse the internal pitch direction of MICROBEAST ULTRA.

3. When you move thrust stick to full deflection the Status LED should light solid, not just flash. If this is not the case increase the servo throw/endpoint of the collective pitch channel in the transmitter for each direction just as far as the Status LED changes from flashing to solid when the stick reaches the end positions. (Note: Do not increase the endpoints too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)

4. Finally adjust the maximum collective pitch when the thrust stick is at full deflection. Increase or decrease the maximum amount of collective pitch with aileron (left = decrease, right = increase). Then move the thrust to full negative and again adjust the pitch using the rudder.

Always set the servo direction in the radio first, then check the display of your BEASTX device and change its control direction if it does not match the real direction. Don't change the internal control direction in order to change the servo direction! This is only used for telling the system in which direction is up and down. Be very conscientious when doing this setup step. Wrong direction will cause loss of control during rescue bailout and poor performance in general!

Setup with StudioX app

1. Move the thrust stick up and down and check whether the pitch is changing direction correctly. If not already done at SETUP MENU point H, use the reverse function for the collective pitch channel in the transmitter to reverse direction of pitch movement in case it is wrong.

2. Afterwards check the Status LED color and display in the app: on positive pitch the Status LED must be blue, on negative pitch it must light in red color. In case the display is inverted (red = positive and blue = negative), reverse the internal pitch direction of MICROBEAST ULTRA by changing the direction in the app.

3. If the stick is not moving far enough, you will see the message "Increase!". In this case increase the servo throw/endpoint of the collective pitch channel in the transmitter for each direction just as far so that the Status LED changes from flashing to solid and the label changes to "OK" in the software when the stick reaches the end positions. (Note: Do not increase the endpoints too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)

4. Finally adjust the maximum collective pitch when the thrust stick is at full deflection for each direction using the + and - buttons in the app.

Always set the servo direction in the transmitter first, then check the display on the MICROBEAST ULTRA and change the internal control direction if it does not match the real direction. Do not change the internal direction in order to change the servo direction! This is only used for telling the system in which direction is up and down. Be very conscientious when doing this setup step as wrong direction will cause loss of control during rescue bailout and poor performance in general!

What pitch is useful for my helicopter?

In general you can say "the smaller the helicopter, the more pitch you have to set". But it also depends on how much motor power you helicopter has, the type of rotorblades you use and finally in what you expect to do with the helicopter. So beginner or scale pilots will not need as much pitch as a 3D aerobatics pilot or high speed flyer. Anyhow, as already mentioned above set the pitch range in MICROBEAST ULTRA so that it roughly fits to your helicopter mechanics and its capabilities.

Heli size (electric)	Maximum pitch
250	13.0 - 13.5 degrees
450	13.0 - 13.5 degrees
500	13.0 degrees
550	12.5 degrees
600	12.0 - 12.5 degrees
700	11.5 - 12.0 degrees
800	11.5 degrees

Heli size (nitro)	Maximum pitch
.37 - .40	12.0 degrees
.50 - .55	11.5 - 12.0 degrees
.90 - .105	11.5 - 12.0 degrees
Gasser	10.5 - 11.0 degrees

Measuring pitch without pitch gauge

If your helicopter is too small for attaching a digital pitch gauge or simply in case you haven't got one you can use a little trick to measure the pitch anyway. You can calculate the angle from the distance the rotor blades move from zero position. Actually this is not as accurate as measuring the pitch with a digital pitch gauge, but it's better than nothing. All you need for this is a ruler and and a good eye. First you need to know the length of the rotorblades from the bolt hole to the outer edge. Usually this matches the specified rotor blade length of the manufacturer. Then you align the rotorhead with the longitudinal axis of the helicopter and fold both rotorblades to one side (as this will put heavy load on the servos it is not recommended use this method on large helicopters with heavy blades!). Now hold your ruler to the blades and mark the zero position. Then when you add positive or negative pitch you can measure the distance between the outer edge of one blade to the other. This distance can be transfered into degrees of blade pitch using the mathematical formula of sinus. Or the other way round you can calculate how far you rotorblades must move away from each other in order to get a specific blade pitch.

Enter blade length in millimeters

Enter blade pitch in degrees